nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I've noticed during a project migration that the FreeRTOS on SDK 15.2 seems to consume quite alot of current, 0.8mA when the SoftDevice is enabled. I've compared to the example...
With any nrfjprog (9.8, 9.7, WIndows 10) I get ERROR: Write verify failed.
"C:\Program Files\Nordic Semiconductor\nrf5x\bin\nrfjprog.exe" -f nrf52 --verify s.hex
I'm able...
Hi
I am using nrf52832 S132 SDK15.2
How many peripherals can be connected to my central device?
does S132 supports only one peripheral connection?
Thanks
Rekh...
Hello,
I am trying to combine Multilink and Uart examples but i have some problems. I followed some steps from other discussions but i'm missing something. I'm a new programmer...
Hi,
This issue is probably more related to FreeBSD than to Nordic specific issues but I was hoping someone had a similar problem and found a solution.
I am using the...
Hi,
Hi, I am using custom board with nRF52832 and nfc. I am using SDK15.2.0 and Softdevice S132 v6.1.0 to advertising packets . I have referred examples\nfc\\record_text...
I would like to know the best place to cut the power in switch off sequence.
We have a IO to totally cut power to the IC (own board), I added PIN control to switch off...
Hey,
I am currently using your product nRF52832 for RF Energy Harvesting applications. We need very low power consumption in sleep mode. In your user guide you mentioned...
Hello, when trying to finish provisioning my nodes (3 total, per example program's instructions), my provisioner program keeps running into
NRF_MESH_EVT_PROV_LINK_CLOSED...
i am using three boards , one is client (nrf52840) and other two boards as server(nRF52832) using light switch example . i want to get the message from client board ,to relay...
Hello,
I am having trouble understanding how the following function in the PWM driver example under peripherals in the SDK. Below is demo1 from the code that creates and...
I am not able to enter DFU Mode with secure bootloader example.
I use IAR and NRF Connect with Programmer to flash
Following are the steps I followed
1. Build Secure...
Hi Everyone,
In this code I'm face a problem. The issue is when i debug, it shows "<info> app: TWI device detected at address 0x6D" . Please find attached a snapshot of...
Hello,
I scrolled through some subjects about that SoC already but I wanted to get some more precision.
1. Can I start developing solutions for AoA / AoD system...
I am trying to do a ramping PWM. I want to update PWM every 25ms by increasing the duty cycle by 10%. I tried to setup a timer, by calling app_start_timer() on repeat mod...
