Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I was trying the nRF Connect SDK but I encountered an error laoding sample program.
I'm following "Getting Started Assistant" instruction.
Python version is 3.7.2
...
Hello Nordic,
As the subject states, why are these two modules still experimental? From what I can see, they were introduced as early as SDK 10.0.0 which was at least 3...
Hello,
for our device we have an input PIN defined with GPIOTE, we expect an event when this input PIN goes from High to Low (interrupt is set by another device on the...
We're using the nRF52832 and want to trap if various parts of RAM are ever executed. We'd like to restrict as much as possible. We run nRF SDK 14.0.0 and SD132v5.
Seeing...
Hi,
I want to migrate BLE HRS peripheral sample to custom board with Raytac's MDBT42-512KV2 (WLCSP nrf52832 used). The board doesn't have external XTAL.
In sdk_config...
I have a problem with understanding reference layout for the chip antenna I want to use in my project. The antenna is ANT016008LCS2442MA2 from TDK.
Based on the schematic...
In my application, I'm setting a message as manufacturer's data to be sent with the advertising message. To do that is simple, since I have a data type ble_advdata_t , and...
Hello guys, I was doing some testing with the QSPI component, and noticed exceptionally high current draws depending on whether the Peripheral was on, off, and if the Macronix...
I’m designing a board with nrf52840. For the RF layout part I’ve followed the reference design apart 3 pads near the pcb antenna.
The question is: How much is indicatively...
working environment:
SDK:12.3
WIN8.1
hardware:nrf51822_qfaa
nrfjprog:9.8.1
problem:
using nrfjprog to program application(s130 + bootloader + application),application...
Hi,guys
I got a problem. I tried to create a service to control led over BLE, when i finished, it can advertise, everything was ok. But when i tried to write 0x01 to control...
BT832 connect to a passiv MEATER temperature senor. How should I configure the Device with AT-commands. I use Docklight to send AT-Commands from my BT832.
Hi Team,
I want to connect the nRF52832 based custom board to AWS-IoT cloud.
The Simcom 2G module is interfaced with nRF52832 over UART.
Can someone guide me from where...
hello everybody,
In my application i want to check if a password is set, to enter bootloader, otherwise don't start the bootloader.
This should work without bonding. ...
Hi, I'm new in the use and development of chip.W here do i start to develop myself?
eg my first aim is to make bluetooth headset compatible with android. Can you help me...
