Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
We use the chip product of nRF52810 to do a wireless module design. While in sleep mode, we found some spikes, which are 0.6mV in amplitude and 180ms in period. It is not...
Hi,
we use CC310 (in nRF52840) in a project (working directly with the CRYS API from SDK 15.2.0). When doing a test of ECDSA with secp256r1, following the one given within...
Hello,
I am trying to change the tx power for my nRF52-DK which is having nRF52832 chip. I trying the following code to change the tx power to -40 dB.
int8_t tx_power_level...
Is there any example about the dongle nrf52840 act as a central? Is that possible? In that case for a ble connection between dongle and board a service does to be create on...
Hello,
I need to long WRITE AND long READ from a central/client (android) to a peripheral server (nrf52). when I says long it means longer than the MTU.
LONG READ
I...
At the top of the Nordic home page, there's a link for "Bluetooth Software":
Following that takes us to https://www.nordicsemi.com/Software-and-Tools/Software/Bluetooth...
Hi!
In a Bluetooth mesh, we would like to get a feedback message from a group of nodes, via a reply message, after sending a message to the group.
The Bluetooth blog writes...
Hi. I am trying to get the peer address from of the peripheral my central has connected to within the BLE_GAP_EVT_CONNECTED event.
The following returns the address, however...
Hi folks,
I try to do create timer. Therefore i want to adding some files in blinky project. So here is some screen shot. Thats about debug error. First i used SDK 15...
Hi team,
I was asked by one of my customers, that if they can use nRF51822-QFAC (existing products design) as peripheral while connected by 2 central (Phone & Router)...
Hi I am a fleding embedded system engineer trying new ways to develop a process( Flashing) in my company,
My company's senior software has designed a control box which...
Hi,
I am facing problem while developing code for the application.
I am working on the "ble_app_uart" example code to develop my one of the application, But after making...
I'm using the code from Vidar supplied here . It works well, but shuts off after 3 minutes.
Based on the idle_state_handle brief, " If there is no pending log operation...
Hello,
I would like to touch on some problem we encountered when using the MPU9250 sensor.
Our goal in the project is to simulate the movements of the MPU9250 sensor in...
When I use the nRF connect app on android phones, the services and characteristics can be detected and controlled correctly, as below.
But when I switch to iOS nRF Connect...
