Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi,
I am evaluating the Firmware on this github repo and my nrf52832.
At the moment I am compiling it using my makefile, however I would like to import this project...
Hi All.
We have flashed the hex-file of ble_app_blinky for pca10040 on the debugger, and things work fine.
We are using sdk-15.2 with softdevice-6.1.1
So, a question...
Hi there, I am having issues knowing how to get access to data coming through a VisualGDB embedded (C) project using the pc-ble-driver. I have my project working fine and...
Hi ,
Nrf52840.SDK15.2,Windows,Ses
Compile "secure_bootloader_usb_mbr_pca10056_debug " project, An error occurred. As follow：
Cannot open file: E:/new/project/wireless...
I have used the UART example up and got it working. So i can send and receive data using it.
However i wanted to modify it so as to run with the current RTOS environment...
Hello
According to BLE Specifications we should be able to get 125kbits/s over the air transmission i cannot seem to get anything remotely close to this.
Is there something...
I use Multilink and Blinky Demo with PCA10056 and PCA 10040 Board,when the two board close to each other there is no packet loss,but when i dispath each other with 50cm,there...
Hi,
I am currently using two different programmers(nrf51DK, Segger flasher portable plus), programming software's ( NRFgo Studio, Jflash). Here are my issues:
When I...
Got this error while trying to perform a DFU over BLE (noble) on a raspberry pi 3. The peripheral should be running v15.
Here is the partial log just before the error...
Hi,
on nrf51 chip we had a reset issue during ESD testing. One of the SWD lines was susceptible to this and caused nrf51 to reset. We had to ground this line after programming...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask if I use pm_peers_delete() to delete a bonding data, Is the data completely erased...
Dear sir.
I have a question about the nRF2460.
As far as I know nRF2460 chip already discontinued right?
The future NORDIC company will not make new wireless audio...
Hi support,
We design a standalone sensor module with nRF52832. We would like to use CR2450 coin battery for power supply. Can CR2450 coin battery be used to supply nRF52832...
