Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi all,
I am trying to interface HI-3585 with nrf52832 through SPI which works fine. Now i have merged the code with saadc program so as to transmit adc values through HI...
Hello.
I am building nRF Mesh SDK using cmake (gcc).
After successful building the code, I flashed hex file to nRF 52 DK.
I want to know free space in DK after flashing...
We want to use nRF52840 as advanced USB - UART converter to control end device (see structure below).
We already checked that our end device is working fine by external...
Dear Support
I’m having a problem erasing the network configuration data in the flash.
We are using nrf5_SDK_for_Mesh_v2.0.1 with the flash manager according to this post...
I am new and trying to install and run samples on Raspi 3B but cannot. Have anyone worked with Raspi 3B and nrf52840 dongle and please give me some instructions.
Hi I'm using Android Studio 3.2 and github.com/.../Android-nRF-UART My Samsung SM-G570Y (Android 7.0 API 24) works no problems but the Samsung SM-G955F (Android 8.0.0, API...
Hi. I am developing a gateway using SDK15 and nRF52840.
I'm advertising 4 devices every 20ms.
Theoretically, it should be scanned 50 times each, but in reality it is...
I tried to add an additional characteristic to NUS service as below.
However, any mobile apps could find only existing Nordic Rx and Nordic Tx characteristics, other than...
- Go to the following link:
www.nordicsemi.com/.../
- Scroll down the page and click the "Downloads" tab
- Go to the nRF52840-DK-HW tab and click "Download file"
...
Dear Nordic Team
-> what is the pinout of the TRACE connector of the nrf52840DK (PCA10056) board ?
I need to connect wires onto P0.11 and P1.00 GPIO, and the trace...
I'm using the nRF52832 SoC through Rigado's BMD 350. For initializing BLE, I'm using the Thingy52 firmware code as the hardware mostly reflects that of the Thingy52. My hardware...
Hi,
I am using nRF_SDK_15.0.0_a53641 and writing a program with keil.
I am receiving data from the sensor with TWI communication and writing it to the sensor by SPI communication...
Hi everyone,
Device : nRF52832
SDK version : 14.2
Softdevice : S132 v5.0
I am facing a problem when changing the interrupt priority dynamically. Let me explain the...
HI,
I'm currently working with two chips RF24L01+.
Each chip switch in sending role to receiving role several times. By default, I set them in sending role and I whait...
Hello
Previous projects used SDK11 protocol stacks with BootLoader and DFU
About the BootLoader of sdk11, DFU is different from sdk15. Please consult me. Thank you.
...
