Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi all,
I am developing for the nrf52xx boards. Let's say I want to migrate the example ble_app_uart from SDK v12.2 SoftDevice s132 3.0.0 to SDKv13.0 SoftDevice s132 v4...
Using SDK13
I have a Central program and I included the peer manager code from ble_app_hrs_c but I am having issues after connecting to another dev kit with Peripheral...
Hi,
I'm using nRF51822 with SD130 (SDK 12.1).
I had a firmware based on mbed that had RSSI update, and it was getting quite a few updates per second.
I've now gotten...
SensirionHumiditySensorsSHT3x.pdf
I'm using a Sensirion sensor (see attached datasheet). I'm running SDK 12.2 and SD132. I've set up the TWI to be a master, and I'm using...
Hello !
I'm looking to combine the softdevice into my .hex file generated by Keil.
Currently, when I compile my project, Keil gives me a .hex. To implement this hex file...
Hello, I received my thingy52 and wanted just temperature ...
I see that thingy is not using ESS - environmental sensing service so I tried to create my own.
(I tried to...
(Building with nRF5 12.2.0 / armgcc)
I want to do bursts of pulses using PWM for the pulses and a TIMER to enable the bursts.
I need this to be non-blocking so I can also...
I am interfacing nRF52832 to run ANT protocol in a custom board. Can I use the nRF52832 to broadcast the data received through the UART port without programming the device...
Hi Team,
We are using board PCA10040 wtih nRF52832 SDK 11.
We got nRF5_SDK_11.0.0_freertos_dfu_060516.zip Production SDK which is working fine for me.
I am using project...
Hi folks,
Currently I am able to do secure OTA DFU on my nrf51822 chip (MDBT40) using the example code provided by Nordic SDK 12 (s130). It works charming!
However...
i cannot able to find the example code in the examples of nrf52 SDK 13.0, am a beginner to this great platform , can anyone please help me for the above problem
Having great difficulty install Python and pip just to generate the keys for secure DFU. This seems like a greatly complex requirement just to be able to use this module....
Currently using nordic52832 to develop products that use batteries.
We found that the problem is that when the BLE module is connected successfully, it takes 200ms to send...
Hi all!
I am developing an nRF52 application that uses RTC interrupt to measure an ADC value every 100 ms. Depending on the measured value the chip shall either go back...
