Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi,
I'm having trouble installing SDK12 on Keil 5.21a
When I run the installer it goes through the process but after the process the files in Keil (pack installer app...
my central application is scanning for, and connecting to, only a single pre assigned peripheral device/address.
This central device is used in a high RF/BLE peripheral...
Hello all.
My product uses nRF51422 and S310 v3.0.0 SoftDevice on EYAGJNZXX by Taiyo Yuden.
When I submit the test plan, I can't find any tested component of S310 v3...
Hello, I've downloaded the lastest SDK (ver. 12) and the installer is only valid for keil 4.
Is it any option to have this SDK working on keil uvision 5 ?
Thanks in...
Hello all,
I just bought the nRF52(PCA10040) DK and programmed the s132 version 3 soft device using nRFgo Studio. Using IAR, I compiled and downloaded the UART example...
Hi,I'am try to update the bootloader. But it stop at 1%. I don't what I miss.
james_boot.hex
james_bootloader.zip
Log 2016-09-06 11_36_54.txt
Dfu_bootloader_via_hex...
hello,
I'm using S132/nRF52/SDK11.
I start a firmware development based on Nordic UART example, I kept the BLE NUS part (I loop back the data received over BLE) and...
Hi All,
Just noticed SDK12 was released last week, with build in support for S132, v 3.0.0. Judging from the compatibility matrix and notes, it looks like it removed support...
Hello,
I'm trying to set a new environment with the SDK12 that'll be less cringy than the one I was running under the previous one.
Basically, what I want is a workspace...
Hi
Using an nRF52832 and SDK11, I have the following issue:
I want to use button 0 with a regular push for functionality and a long press to go to sleep. The detection...
Hi, I'm trying to move from nRF5_SDK_11.0.0_89a8197 to nRF5_SDK_12.0.0_12f24da and faced an issue. I have build error in
....../nRF5_SDK_12.0.0_12f24da/components/libraries...
Hi@all,
i'm trying to connect to a BTLE Printer (printer -> peripheral) from my central (nrf51822 board). But i cannot use the standard discovery examples because i cannot...
Hello, I have pca10001 board and I would like to read an analog input from ADC.
Is there any complete example which I can test using potentiometer ?
Thanks
I'm trying to write some data to flash memory (32 bytes) every 1 minute. the data are not NULL but then I noticed that sometimes (not always) the pstroage module write zeros...
