The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hello,
I run the /examples/ble_peripheral/ble_app_uart application on a PCA10028 using the S110 soft device.
My phone is the motorola G, updated to the lollipop android...
Hello,
I'm working on the PCA 10028 board with nrf51422 with the RTX os (version 4.74.0-5).
My code fails after some time during a call to
osMailAlloc(mq, osWaitForever...
Hi All,
I've happily done all this work before on the Nrf51822 with boot loaders and apps and a happily deployed product.
Thought it was time to shift over to GCC on...
Hi Team,
about power on reset time, not very clear about the description in the SP3.1 as in the attached picture,
why the description are the same?
what's the difference...
Hello,I use s120 and I wnat to send data(write charactheristics value) to all connected peripheral when I receive a character from uart(in uart event handler)?(I use ble_app_multilink_central_s120...
I am connecting to two identical devices, but one is configured as device 'A' and the other is device 'B'. I am currently advertising whether the device is configured as A...
In porting from SDK6 to SDK9, it looks as though
nrf_gpiote_task_config()
has been replaced with
nrf_gpiote_task_configure()
What, if anything, has replaced
nrf_gpiote_unconfig...
I'm using sd_ble_gap_address_set() to randomize mac address and it's working fine. But I'm confused about how to change it back to normal(initial value I see) once I wan't...
i cant find lbs example on \SDK8.0.0\examples\ble_peripheral\nrf51-ble-app-lbs-master\arm and compile.I planned to work with nrf51822 dk. The given example in github shows...
Hello, I have been trying to setup eclipse for the NRF52 off and on all week. I followed the guide on setting up eclipse for the NRF51 and adapted it for the NRF52.
I've...
We have a factory in Hong Kong building and programming nRF51822 modules for us. We may go to a fancier solution in the future, but right now we are using nRFgo Studio and...
If I want to connect the NRF51822 board to Keil using JLink via SWD, I found the SW's clock frequency must below 20kHz. If I choose the higher frequency, the Keil can not...
I know this should be simple, but the prescaler is confusing me...
If I initialize my timers with a prescaler of 0, APP_TIMER_INIT(0, ...)
Then the max timer I can have...
