Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I've built a firmware based on the hci_uart sample with the softdevice controller. The board is custom made and has a nrf52840 on it. Over USB-CDC HCI commands are sent to...
Is there any issue with using the nRF52833 DK/nRF52833 for Matter development? I’m asking because the Matter template doesn’t seem to support the nRF52833 DK/nRF52833. If...
Dear Nordic People Recently I am following YouTube link from Nordic Semiconductor for Implementing ESL https://www.youtube.com/watch?v=VeLkptpSvRQ This video requires specific...
Hello and thanks for reading. Also happy holidays.
We are using an NRF5340, and are having some issues with connectivity. I would therefore welcome any suggestions you may...
Hello
I've been experimenting in increasing the number of targets that a mesh FOTA distribution server can support on nRF52840
The CONFIG_BT_MESH_DFD_SRV_TARGETS_MAX has...
We want to upgrade our existing product to WiFi 6. We have a lot of customization in our TCP/IP stack so we don't want to use the zephyr stack. We only want to make the station...
While in the field test phase of our custom nrf9161 based device, we figured out that there are some towers of some providers that make the device seem online although it...
Hello,
I need to use the Radio_test example on a custom board using the nrf52810. I am using the nrf connect SDK 2.5.1 with VSCode.
To use the Radio_Test example I need...
Mesh 1.1 Generic Location Server defines special values for long/lat and north/east when unconfigured. Current code doesn't appear to support/use these special values, instead...
Hello everyone,
I am developing a ble project that builds on the peripheral Uart example using the sdk 2.4.0 for nrf5340.
I want to implement a watchdog since I sometimes...
Howdy!
I am working with the nRF52840 and currently getting a weird error. Whenever I set the data for the BT_DATA function as anything greater than 110, the system stops...
Hi, I'm using the power profiler II under Manajo with JLink_Linux_V794i_x86_64. I connected my power profiler to measure power consumption, the app (nrfconnect-5.1.0) ask...
I'm trying to use the new GRTC peripheral in nRF54L15 but in various situations I notice that the events are not triggered as expected.
Here is a "minimal reproducible example...
I created project from blank, and added a build configuration. Now it showing as 1 configuration | 2 contexts, as shown in the screenshot below:
What are these contexts...
Hello,
From this morning, I am having issue getting "old" data data on nRFCloud. I tried on several devices, and several features (terminal, log, ...) : when willing to...
