hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I tried to switch to OAT. Now I use new API
" api.nrfcloud.com/.../ long-range/devices/bulk" with OAT bearer token for devices creation
instead of old API: " ">api.nrfcloud...
Hi Team,
Please help to assist below customer concern regarding MPN :NRF54L15-CAAA-R7
They are looking for China typically require a valid Radio Transmission Equipment...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hi
I have successfully added the nrf_crypto files to the UART project. It compiles without any issue. Now I was trying to run the ECDSA example code in the UART project...
I used nrf52840 board with SDK 17_1_0
I used segger embedded studio IDE
i want to Implement two VL53L5CX TOF sensor with nrf52840 so i used two TWI,
but when i init...
Hello,
I'm migrating my project from using child/parent to sysbuild ( simple Hello world code, and using MCUBOOT + NSIB ).
The first error i faced when moving to use sysbuild...
Using Zephyr.
I'm looking for a process or a function to log unconditional message in the logging system including timestamp and other typical logging/display functionality...
We have a custom board with an nRF9160 directly connected to a SIM-S-IO3-MFF2-2 IC. I understand these kinds of eSIMs in IOT devices are typically provisioned over-the-air...
I have a slightly off the wall requirement where I need to send a serial data stream at 5kbps, it will be used to drive an external OOK 433MHz transmitter. The data format...
Hi,
I am having some issues when trying to enable the Fast Pair when executing the bt_fast_pair_enable(). I used the debugger to determine where it's failing:
...
Hello,
I am working on setting up the nrf52 (nrf52832) to communicated with the AD4130 from Analog Devices via the SPI Port. However, I am encountering a problem that I...
Hi,
I'm using the nrf9160, sdk 2.4.0 and tool chain 2.6.1. I need to scan the i2c sensor, I didn't find the i2c scanner example. So i was add one code and tested i'm getting...
I am trying to test the light switch and light bulb example with google home app and google nest device as a border router. I have flashed the bulb example into a nrf52840dk...
Hello, I've been trying to connect to cellular from our custom board (using nrf9160_ns) for the past few days. It already worked with the evaluation board using the same sim...
Hello,
I'm using the audio application provided by nRF. I want my device to play an audio file containing a sound saying "Connected" whenever the board is connected to the...
Hello, I'm running the nRF5 SDK's ATT_MTU throughput example and I want to check that the data sent by the 'tester' (nRF52832 in my case) is effectively received by the 'responder...
Hello Nordic team,
Currently we are developing with the latest Serial LTE Modem FW and modem core firmware which is available on Quick Start.
We see that the COEX0...
Hi
I set the time and date from cfs
the received package is valid. the timestamp is transfer to the set method correctly. the output shows also that the system time is...
