I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi,
I'm trying to control nrf9160 SIP from stm32 MCU via AT Commands. Should I program on the nrf9160 the AT_CLIENT sample for this purpose or is not neccesary?
I'm trying...
Hello Team, We are currently working on a project for interfacing Larger TFT LCD display with Capacitive touch with nRF5340 Devkit board and SoC. As per the datasheet of the...
We use custom board with NRF52840 and a MODBUS CO2 sensor. We are struggling with power consumption when the serial is enabled. The goal is to take measurements and then put...
// <i> NRF_FSTORAGE_SD uses the nrf_fstorage_sd backend implementation using the SoftDevice API. Use this if you have a SoftDevice present. // <i> NRF_FSTORAGE_NVMC uses the...
Hi to all,
I have a problem and a question regarding the power measurement setup I’m working on.
Regarding the problem, I am trying to measure the power consumption...
Hi All,
I have a couple of nRF9160-DK which I use to program custom boards through the Debug Out port. Both DK work perfectly well until now. One of them can't program custom...
Hello everyone,
in our Project we want to use the nRF52840 DK with the X-NUCLEO-NFC08A1 (ST25R3916B) extension board as an NFC Reader.
In the SDK 2.5.2 are samples for...
I am running an experiment to use a static keys for pairing information without breaking the existing flow of pairing/bonding. What I am doing is I am storing the pairing...
I‘m try to download v2.6.0 SDK to update.But the terminal output as follow,I guess it related to bad network also I try with VPN
So that I try to pack v2.6.0 from another...
Hi there,
I'm having an issue with the SPI master in Zephyr. When attempting to transmit data it returns the error: 'Timeout waiting for transfer to complete'. Am I missing...
Dear Nordic-Support,
as I got a configuration error in my project when configuring CONFIG_TFM_PROFILE_TYPE_SMALL=y I tried to reproduce this with the AssetTracker_v2 application...
Hello,
I have a nrf52832-QFAA design that came back from the emissions test lab and they told me that the TX power on the Radio Pin was around -6dBm at the low frequency...
Hello,
I will explain my workflow so you can understand my problem using VS code and assuming everything is installed correctly, I`m using SDK 2.7.0:
Create new project...
I'm debugging the project that nrf_dm to learn how it work.
The build configuration as the picture:
I add my breakpoint as follow:
However,when I start to debug...
Hi, I have developed my own custom module with a program based on the NUS example.
I wanted to use the dongle as a configurator (in the sense that i connect it to the usb...
