We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
I'm writing a custom bootloader for an nRF52840 using the nRF5 SDK v15.0.0. This bootloader uses the SoftDevice to receive BLE packets containing binary data for the DFU....
Hello,
I am evaluating the nRF9161 and nRF9151 and have a few questions.
1. In regard to modem FOTA delta firmware updates, where is the delta file stored in both Serial...
My SPIM seems to stopped working when migrating from NCS 2.5.0 to 2.7.0, so I decided to downgrade to 2.6.0, and it seems the issue is still there. When migrating to 2.6.0...
I have asked this before, but I will ask again.
I have a few questions about the sample source of nRF5340 Audio.
1. Where does the connection process between the gateway...
Hello,
the BSI (German Federal Office for Information Security) released a document February this year which contains a list for recommended cipher suites and TLS versions...
hi ,I am using nrf52840dk- nrf52840 board to interface the IMU Sensor using I2C using nrf connect sdk for vs code. But I am facing error:
i'm using the code in ncs/samples...
Hello im using basic usb over console exaple on my custom board . i believe this task wont require any pins to be configured as my custom board is routed properly to all 4...
Hello,
with the help of this documentation ( https://docs.nrfcloud.com/Devices/MessagesAndAlerts/SetupMessageBridge.html ) i have been able to create a bridge to transfert...
I am trying to test a nRF5340 with a 1.3 inch waveshare 240x240 display using a st7789 driver. How would I connect the display to the board:
VCC
3.3v
...
sdk-nrf: v2.7.0
When PAWR is enabled I no longer get connection timeouts as a callback to bt_conn_cb.connected with the conn_err parameter set when attempting to open...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
Hi,
I am using nrf52832 board and I want to configure the SPI0 and SPI1 for the sensors LIS2DW and BMP388 respectively.
I am new to nRF Connect SDK for VS code, I am exploring...
I have installed version 5.0.2 for NRF connect Desktop and on that I have been trying different versions of tool chain manager ranging 1.3.0 to 1.5.1 none of them is loading...
To measure the current consumption during system off on the NRF52833DK, I followed these steps:
Cut the SB40 bridge.
Connected a multimeter to P22.
Here's what I...
Hello,
I would like to analyze the nfc_launchapp example from the SDK to understand how NFC tags are recognized.
Specifically, I want to examine the relevant code portions...
