Hello,
In October last year I made a Message Routing Service to my azure functions.
From then it worked almost without issue. Now I try to do the same with an azure account...
Hello,
I used to develop for the NRF51822 using the NRF5 SDK in Keil, and I am now migrating my project to NCS. However, I cannot find my chip in the "CONNECTED DEVICES...
I am migrating from the 2.6.1 development environment to 2.9.0 but am unable to compile due to some configuration issues.
My prj.conf configuration file is as follows: ...
Hi,
We have a pretty small device to be designed and I was wondering if nRF54L15 CAAA WLCSP would
have updated recommendations for matching network components available...
Hello,
I've been working with nRF9160 for a while now and wanted to let you know, I love this little piece of hardware. The possibilities, the small form factor, the power...
I have problems with nRF Connect(Android, latest Version, no version number found) to find BLE devices with 2M phy, coded phy and extended advertising. So i am running nRF...
I am trying to implement the following: I have a mesh node built using the Sensor Server example for publishing temperature data. I want one relay node to transmit the temperature...
Hello
I've been experimenting in increasing the number of targets that a mesh FOTA distribution server can support on nRF52840
The CONFIG_BT_MESH_DFD_SRV_TARGETS_MAX has...
We want to upgrade our existing product to WiFi 6. We have a lot of customization in our TCP/IP stack so we don't want to use the zephyr stack. We only want to make the station...
While in the field test phase of our custom nrf9161 based device, we figured out that there are some towers of some providers that make the device seem online although it...
Hello,
I need to use the Radio_test example on a custom board using the nrf52810. I am using the nrf connect SDK 2.5.1 with VSCode.
To use the Radio_Test example I need...
Hi,
we have npm1300 device on our customized board,
without using any of the regulators, LEDs are not connected.
Gpio 0 and Gpio 4 is connected to main MCU.
when activating...
Hi,
Happy New Year! I hope this year brings fewer bugs than the last.
SDK Version: 2.7.0 Board: Seeed Studio XIAO nRF52840 Sense
System Description: I have a setup...
Hi, We are evaluating whether nr54L15 supports LE Audio function? According to the specification, it supports bluetooth 6.0 and should support LE Audio (Isochronous channel...
i want to switch between two code... the code is simple led blinking i am trying for the testing purpose...in my code 1 led1 is blinking 500 ms of delay and in my code 2 led2...
Mesh 1.1 Generic Location Server defines special values for long/lat and north/east when unconfigured. Current code doesn't appear to support/use these special values, instead...
The subject issue is documented here as " NCSDK-20567: Partitioning limitation with MCUboot swap move": This issue has been open for while. These two DevZone tickets refer...
Hello everyone,
I am developing a ble project that builds on the peripheral Uart example using the sdk 2.4.0 for nrf5340.
I want to implement a watchdog since I sometimes...
I’ve been working on creating a C++ application based on the NUS example, but I’m encountering an error. I’ve attached my application below. All I did was enable CONFIG_CPLUSPLUS...
Hi,
I just reinstalled a fresh version of VS Code 1.96.2, and I'm using v2024.12.55 of the nRF Connect for VS Code extension. I'm also using nRF SDK v2.1.1.
In the past...
Howdy!
I am working with the nRF52840 and currently getting a weird error. Whenever I set the data for the BT_DATA function as anything greater than 110, the system stops...
