hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Dear support team.
I'm trying to merge FOTA on nRF5340 on NCS 2.2.0(VSCode). However, after I flash the code on nRF5340DK, it continuously reboot again and again.
...
I would like to know the behavior when multiple Kconfig value settings are defined. Settings are made in the following three places. (app directory) Setting value of NRFX_GPIOTE_NUM_OF_EVT_HANDLERS...
Hi,
I'm having trouble getting the FEM in my Fanstel BT840X module working (the module with the nRF52840 processor and Skyworks 66112 amplifier).
I'm using nRF Connect...
Hi!
I am following the steps shown in video Unbox and get your Nordic nRF9160 DK up and running .
I could flash the SW of the modem, but when flasing the application software...
I'm working on a custom board using an nRF52840 for a sensor Tag (light, hum, temp, press) https://www.homesmartmesh.com/docs/microcontrollers/nrf52/thread_sensortag/
I...
This topic has a lot of info but most is outdated and confusing
For the latest SDK 2.2.0 under Zephyr
-Does the Soft Device have to be disabled before NRF_UICR->CUSTOMER...
Dear all,
I was trying to run example code for nrf52840 dongle. The example exists for nrf52840 Development Kit on this page:
https://docs.zephyrproject.org/latest/samples...
Hello everybody who is familiar with the nRF Connect SDK and NRFX drivers,
I cannot find any documentation about interrupt priorities in the nRF Connect SDK documentation...
I am currently setting up SPI on a nrf52832. I keep getting this error when building "undefined reference to `nrfx_spi_init' ". I do not use the nrfx_spi.c file at all as...
Hello !
I have 2 network interfaces in my Zephyr environment.
Ethernet need 6 byte reservation for link address and own radio driver - 8 bytes.
In you headers size of...
I want to use USB DFU + USB Audio <smp_svr + headphones_microphone>,
but I get an error when use USB to DFU, error log as below. How to fixed it?
*** Booting Zephyr...
Hi,
I've flashed the open thread rcp firmware(from samples) provided by Nordic SDK into the nrf52840 dongle. While running my application, I get the below response for the...
Is it possible to configure TWIM in smbus clock-frequency range (less than 100KHz)? I have created overlay file as follows for nRF52832 based HW, but it has no effect.
...
Dear support,
in nRF Mesh SDK each model can be configured to always publish segmented messages to improve reliability.
For example, the macro for the generic on off server...
Hello all,
I need to use fifo of my project with nrf5340. But there is always full when I put more data in.
Is there a way to make k_fifo bigger?
Thanks!
