Hi,
We are using nrf54l15 soc in our product and using NCS SDK 3.4.0. The LFCLK is set to SYNTH mode where it derives the clock from HFCLK. We have a crystal driving the...
NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
I am running the following Nordic sample on nRF5340 development kits : https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/applications/nrf5340_audio/README.html...
Hi,
We are using the nRF Secure Immutable Bootloader (NSIB) as the first stage bootloader along with MCUboot as the second stage bootloader in our nrf5340 project. We have...
Hi, I just started working with three Audio DK boards. All I'm doing at this stage is trying to familiarise myself with the SDK by building and programming the nrf5340_audio...
Hi. I am trying to mount file system to internal flash memory of chip nrf52840 (using SDK v2.2.0). I was looking for sample and I found some: https://developer.nordicsemi...
OS: macOS 13.2 HW: nRF52833-DK I has a nRF52833-DK and installed the nRF Desktop connect.
use the [Programmer v3.0.4] can't find any Device. I'm sure nRF52833-DK has finish...
hello. I am trying to use nrf52832 only as an MCU without using the ble function. How should I handle my ANT PIN?
Can I handle it like the attached image??
I'm trying to establish a connection with an ICM-20948 via SPI. I check the pins and they are correct but the RX buffer always returns 0x00 when I call to "whoami". The GPIO...
Hello,
We have a IoT edge devices based on NRF52832 with NRF SDK 17.1 with some sensors.
We are facing a problem when we are using both scanning and TWI modules together...
Does the nRF7002 Support The TimeSync
https://www.wi-fi.org/news-events/newsroom/wi-fi-certified-timesync-brings-precise-synchronization-to-wi-fi-devices
Or other tec...
Hi! We're holding a large amount of data in flash, and would like to pass it onto the central when connected.
Currently, we're following this process:
1. Read one buffer...
I've got a new target board based on the nRF52810_xxAA_REV2. I can see it as a connected device in nRF Connect.
I built a new application called CM_Serial using the Nordic...
Hello Nordic,
I want to use SPI master with bluetooth on nrf52840 board. When I use the project under nRF5_SDK_17.1.0\examples\peripheral\spi, I can see the clock signal...
I'm planning on using the nrf connect SDK. And I plan to use the SoftDevice controller. (I want to use TimeSlotAPI)
I have a few questions.
1. Do you have a list of available...
Hello,
I'm trying to configure the BLE stack as non-bondable pairing only so that it requires pairing by every time the smartphone tries to connect to the device (the bonding...
When I debug with DK dev board, data is sent to the virtual j-link com port and displayed on my PC.
When I use target device (using J20 of nRF52 DK) the virtual com port...
