Subject: nRF9151 – EU coverage of mfw 2.0.2 and antenna gain (Schréder Sense One)
Dear Nordic
I'm working on CE and RCM certification for Schréder's SENSE ONE smart-city...
We have an nRF54L15 (QFAA) board, acting as an I2C target ( TWIS30, P0.00/P0.01, address 0x42, 100 kHz ) for an ESP32-S3 through a TCA9406 level translator.
Flow:
Between...
Hello, I am requesting a schematic review of my bluetooth microphone system. I've used the spec sheets as well as audio DK hardware reference material to design these schematics...
We are seeing very high defect rate when installing this part on boards: insufficient solder, solder bridging. When we look at the pads under the microscope, we are seeing...
Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
I am developing an application that involves an nRF52840 transmitting Bluetooth 5 LR coded phy and need an Android tablet to run the receiving app on. There seems to be very...
Hi,
i have a Thingy53 with the Matter Weather Station Example (unmodified) installed, but I cannot commission it into my Apple Home Network. My Network already contains...
Hello,
we have a device in Poland (Orange Poland) which gives the following PSM info:
00> [00:03:30.288,787] <inf> modem: PSM parameter update: TAU: 10800, Active time...
I can build the blinky demo with the nRFConnect SDK and I can flash my PCA10040 DK board from the VS Code tool. But the blinky app does not start - no flashing LEDs.
I know...
Hi Nordic Team,
We have some trouble building blinky app with nrf9160dk_nrf9160_ns board.
Our config :
Host : Lubuntu 20.04
SDK : nRFConnect SDK v2.2.0
IDE...
I'm using Asset Tracker V2
My device is permanently powered, and I would like a quick response time to commands sent from the cloud, so I have turned off the power saving...
Currently in FreeRTOS environment app_timer cannot be used for libuarte timeout. Alternatively, it is possible to use RTC or TIMER. I want to use UARTE0/UARTE1. Then, libuarte...
Hi,
I try to flash my projrect code using vs code on nrf9160dk. It build successfully. But it shows Configuration has not been built. Please give solution for this error...
I created a protocol for packets through CDC ACM, and I send multiple packets if the length goes above 64 bytes. Sometimes I send "request" packets that are received by the...
I am looking into porting an application from a nrf52832 to a nrf52805, but I've been running into a few confusing hard faults. For ease of replication, I found they also...
Nrf52833DK with bmi 270 sample (zephyr/samples/bmi270).
The data has always been odd
ACC data is too high & Gyro data is too low. The Gyro data flips between -1.99 and...
I am trying to implement BLE DFU protocol on my nrf52840 MCU to FOTA the nrf52 devices nearby. I was able to do firmware update by reading the firmware hex stored in RAM and...
I have an issue on 52833 board, SDK 16.0.0, SD s113 v7.1.0 I am using Hard FPU : arm_fp_abi="Hard" arm_fpu_type="FPv4-SP-D16" I have a computation that runs for a few seconds...
Where did the text from this printf go? Which window or tab shows the stdio output? Or do I have to do something in the example's configuration to turn it on?
