Subject: nRF9151 – EU coverage of mfw 2.0.2 and antenna gain (Schréder Sense One)
Dear Nordic
I'm working on CE and RCM certification for Schréder's SENSE ONE smart-city...
We have an nRF54L15 (QFAA) board, acting as an I2C target ( TWIS30, P0.00/P0.01, address 0x42, 100 kHz ) for an ESP32-S3 through a TCA9406 level translator.
Flow:
Between...
Hello, I am requesting a schematic review of my bluetooth microphone system. I've used the spec sheets as well as audio DK hardware reference material to design these schematics...
We are seeing very high defect rate when installing this part on boards: insufficient solder, solder bridging. When we look at the pads under the microscope, we are seeing...
Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
Is it possible to combine both functions in one device (personal tag based on nrf52840) that will enable ibeacon advertisement (to be detected by RTLS scan recievers), and...
Hi,
I am trying to run nrfutil as part of our CI/CD in gitlab. This is a command to install nrfutil:
It seems to install fine however I am getting error:
Any ideas...
Hi,
I am facing a very similar issue like this post.
But I am running DK not PDK. And the stack trace shows the error may be from zb_nvram_load()
All the Zigbee...
Hi.
Problem description
I'm currently using the MX25R64 as an external flash to perform FOTA over SPI on a custom board employing the nRF9160, which is working very well...
Dear Nordic team,
we are evaluating the nRF70 series for an application, where we would like to monitor the radar detection results.
In Linux user space the retrievable...
Hello,
I am working on a custom board which has a multiplexer connected to route two output pins to either UART RX/TX lines or SWDIO/SWCLK.
The multiplexer is controlled...
Hi,
using the example from STM32 Temperature Sensor I was able to create a working program that displayed the MCU die temperature in degrees Celsius every second.
After...
Hi am using nrf52833 for my application , where i need to calculate the pow() so I thought of using zephyr math.h file. it is not working. still getting error saying that...
hello,
planning to do schematic for nrf5340 custom board can i use this https://shop-us.segger.com/product/j-link-edu-mini-8-08-91/ jlink with only taking data,clock,ground...
Hi
on any example in nRF Connect SDK, for nRF9160 (but even for other SoC):
- how can I enable Serial Recovery in the software? any config to select? (I guess I need also...
Hello,
I have found a few old posts about edge detection on gpio using ncs having higher power consumption and suggestions to use level detection.
What is the correct...
Hello,
I am coding on a Seeed Xiao NRF52840 Sense, with the LSM6DS3 6-axis chip. I was wanting to write some code on possibly putting the chip into power off mode, but then...
We are planning to run our application on the 9160 and use the 7002 as for the Wi-Fi connection. They will be connected via SPI. I see that the Location example for the 9160...
I'm confused about the difference between enabling CCCD property without a read property. CCCD means that the client will be indicated/notified when the characteristic has...
Hello,
We have a workspace in the T3 topology (Forest).
Our own module is then in <zephyr_topdir>/our_module and this folder has a boards folder. But when I want to add...
