We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I tried to switch to OAT. Now I use new API
" api.nrfcloud.com/.../ long-range/devices/bulk" with OAT bearer token for devices creation
instead of old API: " ">api.nrfcloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hi everyone,
We are using the nRF5340 and need to use an LFXO, not just for BLE, but also for the real-time clock that our product should provide.
Due to other requirements...
Dear Team,
Just I have purchased Thingy91. Please help with where I can see the demo to start with some basic example of transferring data. Mentioned that Pre-loaded assert...
I just installed the nRF toolchain and Programmer application to start using my nRF52840-DK eval board. I have the board connected through J2 to my computer and I can flash...
hello Nordic
i am using nrf52840 with zephyr ncs
unfortunatly i used this command "pamac install downgrade" at one point
since then i can not use 'west flash --erase...
nRF5 SDK > nRF5 SDK v15.0.0 > User Guides > Developing for nRF52810 gives a list of things to do to adapt an nRF528 32 project to an nRF528 10 target.
But, looking at...
Long story short.
I am trying to merge DFU master code to feed a DFU.zip to the DFU receiver code already present in the secure bootloaders (but elevated successfully into...
I'm working with firmware and hardware that has previously worked properly. I recently migrated to S113 from S140, and changed the data format of what was being set in the...
I am trying to create my first Freestanding Application under NRF Connect, I have SDK version 1.8.0. As soon as I click on "Create Application" I got the error message " Application...
Hi,
I am looking for the sample code of Class B type LoRaWAN end node for Zephyr platform. I am using ncs 1.8.0. I am able to find sample for Class A end node at v1.8...
Hi All,
I recently got hold of some new iBasis Sims and I know that sim card numbers vary from 18-20 digits, where the last 2 digits are the CRC and an extra byte. Where...
Trying to build the OpenThread sample programs (coap_server and coap_client) and am running into some problems that I hope someone might recognize as an easy fix.
In the...
Hello all, This is my first project using Nordic chips and my first project using BT. A lot of firsts :)
I have made a custom board using nRF52820 chip. The board is 4 layer...
To the kind attention of Nordic support team,
I'm introducing dtm files to the project we are working on (fully developed using latest sdk17). We use in this project gzll_nrf52810_sd_resources_gcc...
Hello,
I want to integrate the LwM2M Carrier library for our firmware as we will be certifying our product from Verizon operator.
So, I am able to run the sample code...
I'd like to ask if I request to update the connection parameters via "sd_ble_gap_conn_param_update" and the center for any reason reject the connection parameter.
How can...
