Dear Nordic Team
nRF54L15 is advertised as supporting BLE 6.0. our product is a type of charging case,I would like to know if we need to pass BLE 6.0 certification?
If...
We are trying to bring up a new run of an existing PCB design. No changes in the area of the processor, but a different assembly house. The first call inside ble_stack_init...
Hi Nordic team!
I haven't been able to implement the joiner functionality on a Thread network with nrf52840. I'm using the nRF52840-DK as the leader. For the DK, I follow...
I run a large research lab using hundreds of nRF52840 DKs. These boards are periodically rotated between active experiments and storage. Because boards are pulled from storage...
Hi,
I am using an nRF54L15 and I would like to explicitly enable the HFCLK (32MHz). I want to use it to drive TIMER00, which will run during the whole application runtime...
Hi all,
I am working on a project that requires me to run the SHAKE128 and SHAKE256 algorithms as specified in FIPS 203. I am wondering if it is possible to implement these...
Environment
SoC: nRF54LM20A (cpuapp, non-secure / TF-M)
nRF Connect SDK: v3.3.0
sQSPI soft peripheral driving an AMOLED display via the FLPR
BLE active via MPSL...
Hi.
I'd like to develop my custom board's DFU function like the below steps.
Run my application (simple LTE transfer function included)
During LTE transferring, If...
Hello,
I want to make one fw which adpots for following platform without much changes:
nrf9160 DK
nrf Thingy 91
Both board has nrf52 onboard so, my idea is as...
I have an application where I have configured a reporting attribute which reports on update. It works as expected - until the amount of data you want to send exceeds 8 bytes...
I am trying to find out if I can synchronize the timeslot to a specific time in relation to the start / end of a connection interval. I would also be fine with getting the...
Hello!
I'm developing DFU functions for my custom board.
I have some questions about DFU and Bootloader.
My development environment is below.
nrf52833
SDK 17.0...
Hi,
I am trying to communicate with nRF9160, which is flashed with Nordic SLM application.
I am not able to set the HWFC with UART0/UART2 using menuconfig in Segger...
"Failed to upgrade target. Error is: Lost connection in the middle of the transfer"
I am doing a mesh serial DFU with DFU quick start guide .
I have gotten all the way...
Hello everyone,
I want to be able to set a timer in my project. With this timer i want to be able to make my current comsumption evaluation easier.
I am using the nrf9160...
Cannot update modem (nrf9160) with "nrf connect 3.8.0"
Modem DFU failed with error: no matching trait found
no matching trait found
Installing older versions eg...
The datasheet tells me that the default source of the low frequency clock (LFCLK) is the 32.768 kHz RC oscillator (LFRC). so I took the crystal oscillator off my PCB, but...
After updating NRF Connect v3.9.0 to eliminate the recently documented JSON + connectivity errors with nrf Programmer and Power Profiler, my bash scripts utilizing nrfprog...
Hi，
1. Please provide me with an example of BMA280
2. The SDK: replication v1.7.1
3.IC:nRF9160
4. I tried to change the BME280 driver to BMA280 driver, but the following...
I am working on project in which i want to read data from sd card and send it to mobile through BLE , I am using ble_nus_send to send data but when i decrease the delay then...
Hello,
Using sd_ble_gap_adv_set_configure() with ble_gap_adv_params_t I observe that the actual time when the BLE_GAP_EVT_ADV_SET_TERMINATED event is raised is earlier to...
