Hello friends from all over, I am a beginner. Recently, I have been working on synchronizing lighting animation effects between devices driven by a mesh network and have encountered...
Setup: nRF Connect SDK v3.4.0 (LTS), custom board based on nRF54LM20A, sysbuild with MCUboot as the only bootloader (no NSIB / b0), DTS partitions (SB_CONFIG_PARTITION_MANAGER...
Hi,
We are designing a battery-powered product based on two Nordic chips and would like your recommendation on the overall architecture before we freeze the hardware, having...
Hi,
GSMA SGP.32 v1.3 section 3.8.2 and 3.8.4: the device selects IPAd or IPAe mode with the TERMINAL CAPABILITY command at UICC initialisation. Tag 84 , byte 1, bit 1 set...
Hello I'm developing a project that would communicate with a cellular module using AT-Commands, and voice data using PCM, these cellular modules are always using PCM Short...
Problem:
After every wake-up our device reports a SoC 10–28 % higher than it reported just before going to sleep.
Between sessions the nRF5340 is in System OFF via sys_poweroff...
Hi Nordic team,
While benchmarking quantized INT4 (`s4`) matrix-vector multiplication (`arm_fully_connected_s4` / `arm_nn_vec_mat_mult_t_s4`) on an **nRF54LM20 DK (`nrf54lm20dk...
Hello,
I was wondering if I could bypass the protocols related to BLE transmission (GATT/ATT) and utilize the RADIO peripheral in a close to constant TX rate without regard...
Hello!
Short question: How can I pass a parameter to a SW Interrupt?
Expanded question: I want the board to wait for an ammount of bytes comming from SPI, once this is...
Hi all,
i am really desperate. since more than 1 week i am trying to work with the digital inputs in my custom pcb.
I can set all digital outputs, but from the inputs...
Hi Nordic support team,
We're using nRF52840 to develop a product with lots of features, using nRF NCS latest version (1.7.x as of writing).
Currently we're sitting at...
Hello! I'm working with the nRF5 SDK17 ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_interactive.html ), and I'm...
Hi nordic,
After I transplanted nrf52832 to nrf52833, the upgrade of nrf52833 failed, or stuck in the bootloader.I tried to use the current method to upgrade nrf52832, it...
Hi
Problem description：
In application serial_lte_modem ,When sending AT command "AT + CFUN?"， return"at_host:Error while processing AT command:",What caused this？Thank...
Hello,
We have a nRF52840 on our board, whose fw we would like to be able to update through both BLE and UART (the MCU is connected to a ST32 MCU via UART) using a bootloader...
Hello Everyone,
I am currently using the AGPS example on the nRF9160-DK with nRF Connect SDK v1.7.0. I notice it requires 4 satellites in order to provide a position fix...
Hi,
I need to use system tick to do some math calculate. So I create a new function to get systick like as below. then I can get some number.
And I create a 200ms timer...
Hi,
I'm new with BLE development and I'm trying to find a module that can be used with an Atmega328p and libraries that allow me to create a GATT profile (creating services...
Hello, everyone.
I'm beginner at this, and I need your help.
As the title says, which of the GPIO pins can be specified for PWM?
I am waiting for your answer.
Dear Members,
I want to run :
E:\nRF5_SDK_17.0.2_d674dde\examples\peripheral\spi\main.c
on this line :
APP_ERROR_CHECK(NRF_LOG_INIT(NULL));
I get :
error ...
Hello, I have an application using nRF5 SDK 17.0.2 and SoftDevice S140, I would like to implement the mesh function on my devices and I have some doubts.
1- What is the...
I tested it in a conductive way. The transmission power of +8dbm is set on the software. Remove C3 and L1 and connect the RF line directly to the ANT PIN to test the transmitted...
