Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi,
I am using nrf52832 and mesh sdk 3.1.0 with nrf5 sdk 15.2.
We use dual bank approach for our firmware update with the normal nrf5 sdks ble bootloader. But now our...
Hi.
I have been trying to implement my own Model into the Light Switch Example (Mesh SDK 4.2, SD s140 7.0.1, Hardware: nrf52840 DK), according to this Thread:
Adding Simple...
I'm implementing the WS2812 driver on custom hardware and have some confusion around the hardware tuning parameters for the SPI implementation. The description of the device...
Hi everybody,
We ran into a Zephyr configuration issue which is related to Zigbee and Zephyr's networking stack. In our setup we would like to use Zephyr's modem library...
Hi,
I have nRF52840 DK, for nRF52 series devices. I switched from nRF52 SDK to nRFConnect SDK.
I reviewed
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hello,
I am running ble_app_beacon demo from nRF5 SDK 17.0.2 on nRF52 DK and would like to decrease power consumption as much as possible. From this post , I have seen that...
In the official development board directly burn SDK routines, input the command to write data in the serial port, if you continue to input, for example: interval 1s to write...
Hello everyone:
We use NRF52840 to test the transmission function of mesh and verify the minimum publish(client)-->prescribe(server) time;
The following is the publish...
Hi,
I have nRF52840 -DK boards.
I was using nRF SDK (SoftDevice ) to program nRF52 devices. Now I am switching to nRFConnect SDK. nRFConnect SDK is new to me. A few questions...
hi，
My application MTU exchange is 23 bytes，I send data using Notification or indication to sent 105 bytes date，I subcontracted the data into 20 bytes ot sent，How do I make...
How do I do memory debugging in the nrf52840 in the runtime, or trace the RAM in run time, also how do I do the profiling of the memory in the run time. How do I find out...
Hi,
Iam working on a project based on Ble Mesh, Iam using nrf5_SDK_for_Mesh_v4.2.0_src. Iam trying to form a BLE Mesh network and control the light bulb. For my application...
In my application, I want to implement low power modes and also perform certain tasks like updating the characteristics based on application timers and also update the local...
