The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
In the LTE_MODE_PREFERENCE Kconfig description the CONFIG_LTE_MODE_PREFERENCE_LTE_M_PLMN_PRIO option states that: " LTE-M, PLMN prioritized
LTE-M is preferred, but PLMN...
Hi Team,
We require the detailed procedure for locking and unlocking JTAG access on the nRF54L15 device . Specifically, we are looking for:
Steps to enable JTAG...
The DECT Nr+ shell (the MAC version, not the -phy; tested with v3.3.0-ba167d9f3db4) offers IPv6 connectivity.
The DECT standard has a profile for IPv6 described in ETSI...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi all together,
nrf52810 SD112 SDK 15.3.0
I have a problem writing to flash with the nrf_fstorage module. I try to write an array of 32 Bytes into flash, triggered by...
We currently want to use the USB Dongle nRF52840 to monitor a communication between two Bluetooth devicesand we are new to this field. First we installed the nRF Connect for...
I am trying to build the AES crypto example in the SDK <install_dir>\nrf5sdk\v16\nRF5SDK160098a08e2\examples\crypto\nrf_crypto\aes\aes_all_cli (nrf_crypto_aes.eww).
Compilation...
Hello,
I am using nRF5340DK board and I am trying to enable high-speed SPI pins in nrf5340dk_nrf5340_cpuapp.dts
&spi4 { compatible = "nordic,nrf-spim"; status = "okay...
Hi Team,
We are trying to connect our product (thingy91 reference) to the Link Monitor application to check LTE connectivity and antenna performance.
Loaded nRF52840...
Hi
there are some question regarding this in the forum but I didn't find any clear approach on changing the MAC address.
I'm on SD132 with SDK17 and want to change the...
I just got started with the nrf9160 DK and I tested it with the Asset Tracker application (following the getting started video). At first everything was working fine and I...
If I am creating an application using the Zigbee stack running with nRF Connect SDK and Zephyr, what hardware is not available to me because it is already consumed by the...
I have both a NRF9160DK which I can program and, Zephyr, blinky Serial modem etc, all work on the DK and I also have a nrf91 Thingy.
The Thingy won't respond to programming...
Hi Nordic
One of My customer employs nRF52832-QFAA in their product. They use SDK 17.0.2 and SES to develop their product。
They found the flash is now enough(they use...
I have a NRF52840. To save some energy I wanted to disable the soft device so that there's no bluetooth activity at all. However instead of an average consumption of about...
I am developing BLE Mesh product with `nRF connect SDK`.
I understand most of sample project has a function of proxy node. But I don't know how to connect a provisioned...
I've upgraded several Thingy91 boards successfully with the latest firmware and have ran into an issue with another Thingy91 that I've purchased. Here is the error when I...
