Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi,
I'm working on a project using the gazelle protocol with the gazelle pairing library. Due to the fact that I use the GNU GCC compiler, I created a Makefile from the...
Dear Nordic team,
We have designed custom boards with nrf52840 chip. We observed that in one of the boards the application is not running until the swd pins of the custom...
Hi,
We are using laird BLE653u BLE module in our application. This module has nRF52833 BLE SOC. We have ST Link V2 as a programmer tool. We want to use SWD protocol for...
I have a project using NRF52840 as master in BLE central to scan BLE device.
I found all example will connect device automatically when device found
I would like to change...
Forgive me if this is already discussed somewhere - I'm fairly certain it must have been - but I can't seem to find what I'm looking for. My client's project uses a higher...
Hi,All:
As the topic,which address is the mbr jumping to bootloader by ?0x10000ff8 or 0x10001014? and how to feed the mbr para register 0x10000ffc and the 0x10001018?
Hello,
I need to use the more accurate HFXO for a very short interval to time incoming interrupts (approx 1/50 second every 15 mins)
The processor sleeps idle for the...
Dear DevZone,
I am trying to configure the SAADC on my custom nRF52840 board.
I would like to use it in blocking mode together with oversample 16x and burst enabled...
Why is SES throwing an "Illegal value 0x21009168 written to register 66 (MSP_NS) ignored" message after "Download successful" when programming nRF5340's network core with...
Hello everyone,
I have questions concerning direct advertising. I have read this and other posts from several years ago which provided some useful information.
devzone...
Hello,
at the moment I am trying to get the NRF9160 Icarus Board to communicate with an ESP8266 Board within serial modem mode. I just need to send some AT commands through...
I am trying to install nRF Connect SDK v1.6.0. For some reason the download speed is extremely slow, and even fails without the ability to resume automatically. On two occasions...
I am having issue configuring the chip select (CS) in my little test program. I have read through the SPI drivers and debugged through it and from what I can tell I have everything...
As in fds.h, i am using the fds_record_update() function to update a record, and then as soon it is completed, i want to read the updated data from the flash, but how do i...
