My DECT nr+ PT supports connecting to either of a set of networks, which of course have different integrity and cipher keys.
While scanning for cluster beacons, I can receive...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi everyone,
We have three ADC channels, two of them are implemented as a simple ADC without oversampling, the third one uses oversampling. Because one of them use oversampling...
Hi, I have started development on nrf52840DK . 1-I have installed nrf Connect SDK v1.3.0.
2- I have also installed Segger Embedded Studio Nordic Edition. and selected nrf...
Hello, Please help i m trying to share memory between Network and App Cores in a nrf5340
How To do?
at page 21 Figure 2 Memory Map
it seems that FLASH address 0x0000...
Dear Sir.
Some problem with the PWM .
Pwm output on pin 12 is connected to a buzzer.
When pwm_pin_set_usec(pwm_dev,PWM_IO, 260, 130,0) is set through the pwm_init...
I'm trying to achieve half-duplex UART communication between two nRF52840-DK:s (master/slave) using no external circuitry. I was looking at the thread https://devzone.nordicsemi...
Hello
I am using SDK16, and using BLE sample project (central app_ble_blinky)
when I am taking sample project without BLE , I am able to add UART secure bootloader...
Hi,
I am using NCS v1.3.0 for nRF9160. How to enable both scanner and advertiser roles simultaneously?
Currently even I enable both, HCI LE set random address failing...
Hi,
We are developing the BLE product based based on the nrf52840 Chipset and we are facing below problem while testing in the field.
During our development we have come...
Hi,
Based on other discussions of encryption etc , I created a function to encrypt all the data, so that whenever I call the function It encrypts.
But I am not able...
Hello,
I’m struggling with a problem and need your help. I have an application where a nrf52840 communicates with another nrf52840 over BLE using nus and some services....
I am about to follow the steps here https://wiki.segger.com/Open_Flashloader to be able to program an external flash. However if there is an easier method I would prefer to...
Hello, i would know about the IDE avaiable to develop codes for SoC Nordic nRF52840 and where i can find/download it
Moreover, where can i see examples code about BLE Client...
Hi
I'm working with FreeRTOS with Tickless (RTC) and I was wondering what one should do in order to avoid the FreeRTOS Idle Task to be waken up every time an Interrupt Service...
I have installed SES 5.10a and imported ouf Keil project. There are several issues when I try to compile. This is interesting since I am using the "external" build which should...
Hello,
I have products based on NRF51822, that are central and peripheral.
These products use Softdevice S310, bootloader and application code. It use peer manager, fs...
