Dear nRF team,
When evaluating nRF5340 Audio DK, I noticed, that geometry in documentation differs from actual hardware implementation. Is the documentation outdated or...
Hi,
We are using nrf54l15 soc in our product and using NCS SDK 3.4.0. The LFCLK is set to SYNTH mode where it derives the clock from HFCLK. We have a crystal driving the...
NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
NCS 1.3.0 mbedTLS configuration to the existing app in SES results in compilation error.
The SES project file contains the define like so -DMBEDTLS_CONFIG_FILE=\\"nrf...
I recently came across the Smart Remote 3 product by Nordic. I currently have a product in development that is a remote that has very similar functionality. Even down to the...
Currently I am facing an issue where the board was not able to power up by itself when a USB is port into it. However, when an external source is connected through the debugger...
Hello,
I have a costum board with nrf52832 chip. when I upload example code "/examples/peripheral/uart/" I can see logs coming and loopback test is working great, but when...
I am inquiring about a custom device that hangs in the ble_stack_init(); and the result is a fatal error.
The custom device has an nRF52832
The SDK is the SDK14
The...
Hi,
I am using NRF52810 which acts as a peripheral to send data to the central . The problem is my device is battery operated,So advertising all the times consumes battery...
Hi,
I have Design a new product based on the NRF52840 I am trying to get the lcd up and running so first thing is the pwm for the backlight. I am using pin 1.08 for the pwm...
Hello everyone, We're using a NRF52840 dongle for a Uni project. We got a couple of dongles it. I stupidly used a image on google to know the pinout because it's hard for...
I am trying to use the BluePy Scanner on a Raspberry Pi 3 B+ with a nRF52840-Dongle programmed as a Bluetooth: HCI-uart .
I am able to get the Bluepy Scanner code to work...
Hello,
I have nrf52DK and I want to deploy templates from S130 protocol to NRF51822XXAC. Any tutorial or guidance would be greatly appreciated.
Thanks in advance.
Hi to everyone!
I am working on the SDK 17.0.2 and my project contains nrfx_twim.h functions.
I have a problem to understand the changes that i have to make in the sdk_config...
hi..
I am using nrf52832 and 15.2 version sdk . my laptop 64 bit wndows , there is no software for 64 bit windows , so i installed the 32 bit software
i am getting the...
Hi, I'm just wondering if there could be any chance that the GPIO can be used as ADC? I had my gas sensor output wired to GPIO (P0.03) instead of ADC (AIN0-AIN7) pins. TIA...
