I am using the following version of nrfjprog on my Windows 10 machine:
nrfjprog version: 10.24.2 external JLinkARM.dll version: 8.44a
Most of the sub-commands work with...
the older nrf52-DK has a header for external and one for current measurement.... how do i achieve something similar on the nrf54L15-DK, which exposes the 3-pin P6 header?...
Hi,
I am developing an acoustic platform with my custom board with a nRF5340 CLAA chip. The board is recording audio data from two microphones at a sampling rate of 100...
I attempted to create bluetooth central and peripheral apps using two nRF52840 boards that connect to each other and no one else using the device name. I had limited success...
Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
Hi, We have used nPM1300 on our development board around nRF54H20, but we are experiencing an strange issue. - when power is attached VBUSINILIM0/VBUSINILIMSTARTUP value is...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
Hi,
I am trying to modify the code in the BLE_App_Buttonless_DFU_pca10040_s132 example is SES. Without any modification the code compiles fine and can be recognized by nRF...
My issue like this ticket
https://devzone.nordicsemi.com/f/nordic-q-a/39428/usb-msc-corruption
I suspect it is caused by a problem in the implementation of the NRF_BLOCK_DEV_QSPI_FLAG_CACHE_WRITEBACK...
Hi,
We encountered a problem when added new models through an OTA DFU. Specifically we upgraded a device with SoftDevice 6.1.0, SDK 15.2 and Mesh SDK 3.1.0 to SoftDevice...
Is it enough just to connect from custom board to P20 header(nrf52840-dk) SWDIO, SWCLK, RESET, from custom board GND to P20( GND_DETECT) and power supply to custom board from...
I need to enable UART1 in runtime in order to be able to read some data coming on that device.
In order to be able to use the uart functionality, I need to set CONFIG_SERIAL...
Hi,
As the subject description, I just remove the part of hid function from main.c then make the personal source file.
Before I removed, the project could work as usual...
Dear Nordic
there are two question find in my software. it may be some matter with thest two question, so put here together.
1.
My software will be reset about several...
for the i2c_3 to work the following is needed to modify the SDK.
nrf/subsys/spm/Kconfig
```
config SPM_NRF_TWIM3_NS
bool "TWIM3 is Non-Secure"
default y
```
...
I was wondering the behavior of the NFC BLE Pairing with OOB when max connections are full. Will the connections disconnect in order to pair with a new central after an NFC...
Hello,
in nRF52832 devices, P0.21 pin can be configured as reset using PSELRESET[0], PSELRESET[1] ergisters.
Due to space constraints, i dont intend to use the reset...
Hi：
I want to ask：the nRF24L01 can work in single point mode by SPI commands。 I need the wave show like in the picture。
IF it can,which software and hadware I need....
Hi,
I trying to send indication supplied with some data to my Android app (which BTW works fine with other BLE devices) as an answer to characteristic write command
...
I am trying to run a project on a Fastnel
BT840 module
I had the code running on The dev kit when we switched to the new hardware without a FL crystal I have been unable...
Hi,
I am working on writing data on flash and reading it back.
i am not able to read data which i am writing to it . i am posting my flash file please suggest where i...
