Hello,
I am experiencing an issue with my nRF52 DK. The target nRF52832 appears to be working, but the on-board debugger is not functioning.
Symptoms:
No power/debug...
I have two nRF9151 DKs and want to evaluate direct, SIM-free DECT NR+ communication using FT and PT roles. Please help me with:
- DECT NR+ MAC/PHY modem firmware, rather...
I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
As you will see with my simple files I have followed about 3 different tutorials to get to the point I am at. I am trying to replace the included SALSProbe.ino program with...
Hello,
I'm trying to program an nrf52 PCB I created from Arduino and code studio just trying to upload a simple blink but when ever I try to connect any of my ST-link...
Hello
I have defined the SPI pins in the sdk_config of the ble_app_uart example and compiled the code after adding the dependent drivers from spis project as shown in...
Hello,
when writing content onto the CDC-ACM interface of the nrf52840, I sooner or later always end up in a Segmentation fault.
I'm on nRF52840 and using the SDK v16...
I'm using the nRF52840-DK evaluation software from Segger. I want to add NAND Flash support, so I want to add an SPI interface. I have looked at the example in nRF5SDK160098a08e2...
Hi，we had finished application development on nrf52832 long ago, based on nrf52 sdk 14.0(with softdevice 5.0). But now we get feedback which is a bug has been fixed on sdk...
Hello guys,
I would like to know something more about the scheduler whose implementation can be found under SDK_ROOT/components/libraries/scheduler .
Our idea is to apply...
1. I don't want to call the fds function when enabling or disabling cccd: pdb_write_buf_store, so I did the following:
2. I am in nRF5_SDK_12.3.0_d7731ad in the sdk Routine...
Hi There - I'm very new to electronic design and need help making a key design decision. Specifically I want to know that the performance will not be a problem when writing...
Hi
On some devices we see in the production a shortcut between the BT antenna and the P0.18 pin on the 52811. The cause can be extremely warm weather at the production facility...
Hello,
We are tweaking the TLS connection between nrf91 and mosquitto.
What ciphers does the modem support? Is there a list available?
Best regards,
Vlad
I want to send a byte on Nrf connect app upon receiving an GPIO interrupt using BLE_APP_UART code. I have configured pin P0.10 for the GPIO interrupt. I am using SDK15.2.0...
Dear guys,
I am implementing a module that monitors the battery voltage for our tracker device using NRF9160.
I do not understand how to set up two parameters for the...
Hi:
The urgent problem we are facing now is:
debugging hci_usb on Linux, how to set MAC address and send/receive files ? hci_usb fw : \ncs\v1.3.0\zephyr\samples\bluetooth...
