Hello,
I have not found any information about the VBUS current consumption. Is this information available? Do you know how much current flows through the VBUS pin?
Thank...
I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
Hi,
I developed a software (based on SDK V15.3) that works very well in ESB timeslot with a BlueTooth connection. The softdevice version is s140_nrf52_6.1.1.
Today, I...
I am new with the nRF52832. I need to develop a bluetooth slave port for an existing controller. The controller will communicate with the nRF52832 via the UART. For prototyping...
Hello,
We use the NRF52840 dongle in a production environment. Currently when we buy more dongles to add them to the line, we have to program with NRF Connect to get the...
I have a created a custom service and a custom characteristics. The characteristics has both read and write properties. Now I want to authorize the read and write opearations...
Nordic,
We have added Background DFU(Application DFU) in our code and it works for App update. Now i want to add support for Softdevice and Bootloader update in this. Will...
I'm working on setting up a Fitness Machine Service on our nRF52832 custom board.
When I add the Training Status characteristic SIG 0x2AD3, I get Unknown Characteristic...
Hi, I am looking where can I get the ACK from the light bulb, in Zigbee light control example. I am using the latest sdk nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
what...
Hi,
The documentation for the simple_on_off model in the nRF5 SDK for MESH v4.1.0 states that the light_switch example uses the simple_on_off model.
The documentation...
I think spi slave pins should set as input but I want to control CSN pin as output in spi slave mode on nrf52840. Is it possible it?
I know that CSN pin is controlled by...
Thingy91 is useless without working samples and SDK
Out of the box it cannot associate with any NB-IoT cells here in Bulgaria. I tied using the provided SIM card from iBasis...
Hi I am having some trouble changing BLE connection parameters (mainly due to the connection handle). Is there any working example that I can refer to, which explains how...
Hi Nordic folks,
Our project is using nrf52840-DK boards as the development beds. We're developing a security application by leveraging the internal CryptoCell CC310 inside...
Hi everyone,
I successfully tested the example of the MQTT publisher in the IOT sdk on a NRF52840 and a raspberry pi 3+. The messages end up in my mosquitto install and...
Hi,
We have seen random ARM faults.
After some time we have seen that the lr register often pointed to entropy_cc310_rng_get_entropy.
This is our setup:
- Environment...
I recently purchased nRF52840 DK. While scanning through the website, I came across a suggestion to start with Blinky example. I opened the project in Segger Embedded studio...
