Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
Hi,
I am using the softblink library in SDK 13.1 to control a RGB status indicator LED. It works fine, until I want to change the PWM settings or the LED pin.
The change...
I'm developing an interface I2C to one sensor including SCL, SDA and open-drain return to know if
the sensor is ready to work. After Reset by "Build and Run" form Segger...
Hi,
I'm a new guy for the development in nRF52840 and try to build the application by using 802.15.4. I have two questions, as follows:
Firstly, when I follow the instruction...
Hi, environment is nRF5_SDK_16.0.0_98a08e2 windows SES target is nrf52840. I am using the nordic dev board. The final product is a wearable, which will connect to a smartphone...
Hi All,
I'm using NRF52832 for our product. I test bootloader functionalities with development kit. The software system is also tested separately by directly programming...
Is it possible to achieve 2Mbps real speed when sending 2Mbs of data in BLE.50?
It supports USB 2.0 H / W, but the actual speed is full speed. Is high speed possible with...
What is the need for a provisioner? Is it mandatory to have provisioner while client and server communication? In which condition provisioner needed in mesh network? Which...
Hello,
This is more a question than a issue. I am working on a sample to transmit data from MOSI of the SPI to UDP. It is possible to see received data through SPI on LTE...
I would like to make a timer to check the GPIO status.
The current code is like below:
I already checked that timer function is worked by implant the specific event...
Hi, I am developing sensor reading via ble using nRF52 Development Kit from scratch.
Since bluetooth, nrf, sdk stuff are a whole new world for me, I m following step by...
Hello All,
Recently I got the nRF 52840 PDK kit and wanted to start with a simple example.
I tried do the following. It works but when I use the following it doesn't....
I want to use Termite by UART. but failed. Is there any option left other than RTT ??
So how do Window user communicate with the board ?? I need to send data from mcu...
Dear Tech Support,
I'm currently working on implementing the Flash Data Storage library and ran in some problems. I'm using SDK 15.3 with softdevice s140 and a custom NRF52840...
Hi,
I'm trying to run the basic blinky exemple from 15.2 Nordic SDK on my nRF52480 hardware and get data on a puTTy window.
Unfortunately the putty window itsn't printing...
