Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
I have an application built on the 52840 which is using a software interrupt triggered by the event generator unit. Occasionally my SWI function is being passed a zero for...
Hi everyone,
I want to set by BLE device advertising itself for 30s and then go to sleep. To that I set the APP_ADV_DURATION = 3000. What is not clear to me is the difference...
Hello ,
I am playing with PDK NRF 5340, I am trying to write a simple code to configure a PIN (0.10) which is not already in use by PDK.
When I print it's state it always...
Hi,
nRF52 SDK Version: 16.0
Example: examples/ble_central_and_peripheral/experimental/ble_app_multirole_lesc
File: main.c
I made two different binaries of this code...
Hi,
My question is about Nrf connect for mobile but I could not find that in the product dropdown list.
I am trying to analyse packets between my mobile phone and...
Hi all,
i am using twi_scanner and twi_sensor as templates to get data from CCS811 Air Quality sensor with PCA10040 and SDK 15.3. But i cannot get the data printed in...
I really don't understand your terminologies. In beacon example you are passing BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED. It is getting scanned in NRF CONNECT...
Hi,
Trying to implement ECDH I struggled creating the random seed. Using Nordic Security Backend and Vanilla Mbedtls on the nRF5340 I get the following errors:
Minimal...
Hi,
I am developing the board to act as Broadcaster and also Observer
I am using SDK_16 with SEGGER EMBEDDED . nRF52
board wants to do Broadcast the signal ( non-connectable...
Figure 7 of the nRF24L01 data says ACK payloads must be loaded in advance to the automatic ACK transmission. I wish to make the ACK data packet dependent on what is received...
Hi：
I noticed, P0.18 P0.19 P0.21 P0.22 P0.23 P1.00，recommended as QSPI.
There is no way to raise the P0.22 pin using this code.
But my own board must use P0.22 as...
I'm been analyzing this code for a while now but can't see how this code actually triggers a switch into the Bootloader mode. There are no references to any resets or the...
Hello
I would like use at least 2PPI channels to control a GPIO.
If PPI CH0&CH1 both setup, then GPIO_CTL just go high.
If PPI CH0 remarked, then GPIO_CTL go low
How...
Hi, 1. What document can guide the macro definition of configuring the nrf9160 project? 2. How do you know that prj.conf has those macro definitions how to configure? 3. A...
