Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi,
I want to get Battery ADC Value.
So. I simply used nrf_drv_saadc_sample_convert() function.
At first I thought it was the right value,
Later, I found that the...
Hi,
I want to get Battery ADC Value.
So, I simply used nrf_drv_saadc_convert()
At first I thought it was the right value,
Later, I found out the wrong value.
If...
Hello, Nordic.
I am working on an iOS App that uses a MPU9250 sensor to display a 3D simulation screen in my app. (It is same as motion control in Thingy52 App).
I...
Hi,
I am using PCA10028 development kit for sniffer with wireshark 3.0.1 using sniffer version V2.0 beta 3 . I am getting issue like "Encrypted packet decrypted incorrectly...
Greetings,
I was wondering why Amazon FreeRTOS demo wont work on nRF52840 DK. After following all the steps even building a bootloader on my board, my demo is running but...
SDK 14.0,
IC:NRF52832
I want to save some data in the flash via the FDS. firstly i write 3 records then the next I want to read them one by one according to the record...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
1) If I configure any GPIO as state change trigger...
I used Win 7.
I updated the nRF connect application to use with the nRF dongle.
The Microsoft wireless mouse and keyboard is shown like nRF Connect DFU Trigger. Also internal...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex?-M4F 32 bit processor...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
1) What is the difference between High-accuracy...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
In https://devzone.nordicsemi.com/f/nordic-q-a/47707/how-to-use-sd_rand_application_vector_get-correctly, you suggest to wait a couple of milliseconds if I run into NRF_ERROR_SOC_RAND_NOT_ENOUGH_VALUE...
Hellow everyone, I'm testing the UART communication between the MCU and the PC. There is communication in both directions, the problem is that even if you only press the keyboard...
