Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
The documentation for the nRF52840's SAADC mention optional resistor ladders. What are they for? I see that the documentation specifies that the ladder's resistance is 160kΩ...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
I got this info when I use keil to download progream though jlink.my board is NRF52832,the version of my keil is V5.24 and the version of my SDK is 14.0.
why it's happened...
Using SDK 14.2.0 and PCA10056 Dev kit: when I load the example (usbd_cdc_acm) and flash it, it works well, can communicate in both directions (windows 10 and debian linux...
During more than two years SDK contains OTS in 'experimental' mode. Do you have any plans to update this service (and write an example how to use), or better avoid using this...
Hello,
I updated Segger Jlink software to the last version and there is an issue with the nRF52840 preview DK.
Segger gives popup about updating firmware but it cannot...
I wonder if Nordic reveals electrical schematic of IO buffers?
I have taken some current consumption measurements recently and I have realized that setting a pin as input...
Hi,
I am working with nRF51822 and softdevice.
I am trying to modify the radio output power without success. How can I do that?
I have found a softdevice function...
I have been researching BLE 5.0 for the feasibility of Nordic Bluetooth chips in our new products.
I have read many times in the general internet posts that BLE 5.0 devices...
I have a characteristic that is write only and required authorization on write. [I have "successfully" implemented this on several characterteristics previously.] The write...
Hello. I want to extended data length in my firmware which is based on ble_app_hrs example. But, when I try to set NRF_SDH_BLE_GATT_MAX_MTU_SIZE 247 (it was 23) I get two...
Hello. I want to extended data length in my firmware which is based on ble_app_hrs example. But, when I try to set NRF_SDH_BLE_GATT_MAX_MTU_SIZE 247 (it was 23) I get two...
We are currently going in production with NRF52 and we are facing the following issue with RBP on NRF52832QFAAB0.
Basically looks like the processor enters an unknown state...
I have changed the UART or nus_central program in order to be able to connect 2 peripherals to 1 central. Everything seems to be working on the central, no error appears on...
Dear Nordic team,
I am working on ble_app_beacon example code (v-11.0.0-2.alpha) to add the support of DFU (firmware update). I have experience with hrs_dfu example but...
Hello Friends,
im new here. It is the first time with the development of a Bluetooth device. I want to use the NRF52832 Chip.
But what are the biggest diefferent between...
Is the nRF24E1G obsolete?
If so, is there a drop-in replacement for the nRF24E1G.
We currently use the nRF24E1G in a product and have heard that it will no longer be produced...
