Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Greetings,
I'm having trouble being able to perform a DFU with the secure serial DFU. My setup:
Using PCA10040 (nRF52832) with the s132_nrf52_4.0.2_softdevice.hex...
Hi.
I am using saadc sample cod of SDK13. Changing some parameters based on the analog input, the example is sucking somewhere where I have not been able to find it.
...
Dear all,
I am facing small problems, which I guess most of you faced at some moment.
I am trying to switch from working with ST microcontrollers to working with nRF52...
Hi,
I know that the default handle value of device name is 3, but in my application i am not getting the default device name handle, is it possible to change the device...
I want to save precious CPU cycles by writing 40 i2c (TWI) registers in one shot. Can I somehow set up the TWI master to write 40 registers (each 16-byte address with 8-bit...
What is the maximum length of pdu for ble advertisement? I have ported the example application of solar powered beacon without softdevice.
I just wanted to know if it was...
For what I understand of the doc and this question it is possible to turn off the SD, turn it on later and then use the settings as normal.
Is it possible to turn on the...
Using nRF52; S132 v4.0.3
I'm getting NRF_ERROR_DATA_SIZE error return from sd_ble_evt_get and event length from call is 20 which is smaller than my buffer so it shouldn...
Hello everyone,
Currently we're writing a small program for the NRF52 (PCA10040), which has to communicate via SPI to an IMU (MPU-9250). The code is working correctly,...
Hi,
I am using SDK 11 , nRF52 DK . IAR 7.5
In current implementation I am flashing a sofdevice s132 and the bootloader by the nrfjprog.exe but if I am flashing the app this...
NRF52832 S132 MPU6050 TWI
I want to finish the function:
1. When the ACC, GYRO data update, the INT pin to generate an interrupt, and then in the P026 pin configuration...
hi team,
i need to receive data via uart0 without uart_irq handler. i am using simple_uart .h library. please any one reply me...
need urgently...
thanks advance
