Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi team,
I'm using the NRF54L15DK board with NCS SDK v2.9.0.
I'm trying to include the B0 bootloader along with the MCUBOOT and application.
I'm wanted to customize...
As subject, the key is using prj.conf, compilation errors will occur, if do not use prj.conf, c ompilation pass but 54L15 not work(no logs aft pwer on). Is fast pair(locator...
Hi, I am currently migrating my project from nRF Connect SDK v2.5.3 to v2.9.0 / sysbuild.
Unfortunately, my devicetree configuration for a mcp2515 CAN interface is not accepted...
Hi, Nordic team
we want to develop indoor tracking system using nordic soc chip we saw some sample codes from your nordic sdk 2.9.0 , we need any research papers or documentation...
While experimenting with the v2.6.0 set of matter examples, it was noticed by an associate that the LightSwitch example doesn't seem to want to connect to any networks. This...
I am using NCS v2.9.1 and trying to enable a bootloader chain with NSIB and MCUboot. The regular setup works fine, however if I try to enable the minimal configuration, I...
Hello, just like the title indicated, I need help with setting up the nRF21540 EK with the nRF9160 DK.
For my application, since the nRF9160 DK has the nRF52840 on it, I...
Sorry for the inconvenience!
I have downloaded V2.8.0 nRF SDK, and I use this command to build light bulb project:
west build -p always --build-dir nrf/samples/matter...
Hi everyone,
I’m working on a project involving the nRF7002DK, where I’m trying to combine two separately working applications:
A TinyML CIFAR-10 image classification...
I am attempting to configure and build the Asset Tracker v2 for my Actinius Icarus v2 board.but the build is failing.
Setup:
nRF Connect SDK v 2.9.0
Board target:...
Hi,
I am trying to build an application using the nrf54L15-dk board and want to use the board as a controller. I run the application on the external host but got an error...
Hi, Any one kindly suggest and Chip based antenna for the Thread + BLE and Wi-Fi + BLE protocol in NRF54L15 protocol. Also kindly suggest the PCB based antenna for the Thread...
In the past few months I got aware, that some, in my opinion simple questions, get marked with
"This comment is under review"
and then nothing happens. For weeks, even...
Hi all,
I'm doing some tests with the nRF5340 DK to log with a custom timestamp source. I took the logging exercise 2 example and verified that the log messages are correctly...
