Hi,
I’m using the function lte_lc_psm_param_set(rptau, rat) . After connecting to LTE, I call lte_lc_psm_get(&psm_cfg.tau, &psm_cfg.active_time) and receive the following...
Hi,
Developmente setup: Windows x64, nrf connect for vs code, SDK and toolchain versions 3.0.2.
I was trying to build a proyect for a custom nRF5340 board when I encountered...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I am using the S312 protocol stack on nrf52810, with both BLE and ANT+enabled, to transmit heart rate. It can be used on most devices, but it is difficult to connect to 'wahoo...
Hi all,
i need to read the status on my GPIO where there is a led.
I have configured it like a:
nrf_drv_gpiote_out_config_t configLed = GPIOTE_CONFIG_OUT_SIMPLE(true...
Hi. I'm using nRF51822, SDK12.2.0, S130 as multi-link Central.
#define SCAN_TIMEOUT 10
Time-out is working well when it is Single connection. After 10 second, it stops...
How i can see the performance like the Picture. is allways 0% and had also no time or calls in the execution profile. Breakpoints works.
But when i press F10 (Step over)...
Hi There -
I'm trying to test connection interval negotiation with a central by putting nRF Connect Desktop (Mac) in peripheral mode and requesting a connection parameter...
I have a nRF52840 application that needs to take a complex list of commands from a server.
I have a few options. I could:
code a basic language myself for these commands...
HEllo
I am using the example TWI_sensor_pca10040 with a main.cpp, and I see that there is some sort of error with the logging that I cannot point out. I get this error...
Hi
I'm currently working on the 10028 DK board, which was working flawlessly until I used the J-link RTT Viewer, and pushed the IF BOOT/RESET-button. Now, when I try to...
Hey,
SHORT VERSION:
Timer (every Second) gets started when connecting (BLE with nRF Connect) to my DK (SDK12.2, Softdevice S132). Timer gets stopped when disconnecting...
Hi There,
We have an issue where our project crashes, but the app_error_fault_handler() callback is not being called to help identify the cause of the issue. We are using...
Hello guys.
I'm newbie to embedded programming.
I'm trying to make device that can measure temperature of other objects. I have a variable resistor. The resistor's resistance...
My BLE application uses my own firmware update algorithm and bootloader, as well as the Peer Manager module. To ensure that I do not delete peer data during the update process...
I am using nrf51 running as a peripheral and an iphone app as central. It works OK when I first use the iphone app to connect to nrf51. Then I quit the iphone app and let...
Application data is stored just before the bootloader. If I do a DFU upgrade with a larger bootloader than the one currently flashed, is this taken care of? That is, is the...
i am using keil mdk5 and i want to use nrf51822.please tell me which software i need for this and which sdk i have to download for this.i am currently troubling with doing...
