We are seeing the same thing as in 129099 (case 362913) and 129410 , found independently on our side. We have narrowed it down a bit further, so we open a new thread with...
We are investigating an intermittent Bluetooth Mesh LPN issue on the nRF54L15, where the LPN state machine becomes stuck in BT_MESH_LPN_ESTABLISHED even though the Friendship...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
Hi,
On the nRF93M1 DK, we can switch between physical SIM and eSIM with %SIMCFG="SimSlot" (mfw 1.5.0).
1. Is SimSlot written to NVM on set, or in the flush at CFUN=0?...
Hello, I've built sample aws_iot for target nrf54l15dk/nrf54l15/cpuapp, using the provided .conf & .overlay files for nrf54l15dk using NCS 3.4.1. The certificates and keys...
We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
Hi
When I reduce the operating voltage, the nRF51822 with the heart rate demo running resets whenever the voltage drops below 2.1V and does not recover unless I increase...
I need an star network with 1 master and 4 to 8 slaves. I'm not so concerned about the power, but the convenience of the nRF51822 is attractive.
Does the current BLE library...
Dear all:
Now,i have issue ,i can't fund device.(i have sure the hardware is OK)
i think it is program overwrite the J-TAG register(TDO)? but i may not sure.
have any experience...
The Arduino SDK by David Edwin linked to here is no longer available since the Bluetooth forum seems to be down, and has been for some time: devzone.nordicsemi.com/arduino...
Hello and Happy new year!
My goal - to create ibeacon device. I've bought evaluation board, wrote firmware implementing beacon role and loaded it into PCA10001. It works...
I've modified the simple_uart example to use app_uart instead but I cannot get any data transmitting. I know the connections are correct because it works fine under normal...
Ole Morten has suggested using command-line GDB in a number of postings on this forum. Accordingly, I've tried to do that but always getting the following error ("Cannot find...
Dear Nordic
Does Nordic have a passive writable chip available (with compat antenae) that can be activated by mobile device bluetooth scanning event. The mobile device...
Hello
I am trying to run the dual mode BLE/Gazell application example ble_app_gzll. I adapted it slightly such that the stacks are switched automatically in main() as follows...
Hello
I'm using nrf51822 EK board. This is my first time to develop application in ARM system.
I want to develop a ble application.
This application can be shut down (system...
I've got my custom PCB design assembled. Attached segger jlink, but it detects only 0.1 V, although Vdd is 3V.
How is the power measured?
What should I read on SWDIO...
Dear
Is there a possibility within Nordic SoC to make a passive RFID Tag which will connect to SmartPhone via Bluetooth?
Just like µBlue Series, but smaller and using...
I found the "S110_SoftDevice_Specification_v1.2.pdf" but not the "S110 softdevice release notes" mentioned in a previous question about DCDC usage. Where is that doc?
What...
I have been developing on a nrF51422 QFAAC0 chipset. That chipset required SDK 4.4 for soft device capability.
I requested the latest silicon (so I could develop against...
