We are seeing very high defect rate when installing this part on boards: insufficient solder, solder bridging. When we look at the pads under the microscope, we are seeing...
Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
I have implemented my own I2C driver and I am getting issues with NACKs.
On review my code is doing what twi_hw_master.c is doing.
I then went looking for a Nordic sample...
We have developed and certified a module which uses the nRF24l01+. We spent a good amount of time tuning the antenna circuitry which has resulted in very good range... in...
Hi,
how to get into the bootloader mode without pressing any button, when some application is running? I also tried it with setting the NRF_POWER->GPREGRET but it is not...
I am looking for a minimalistic schema design using BLE for collecting data from i2c (twi) sensor and sending them over blue-tooth to the receiver. I need the following features...
Hello,
I would like to know if there are any restrictions in the amount of external memory (RAM, Flash) that can be added to a system using a nRF51822. In that case which...
Although there are some posts dealing with bond manager issues, I have not been able to find a similar issue. I am using part of the BLE code from nRFready Desktop 2 v1.0...
Hi,
i have some trouble with acting with the nrf 51822 ADCs. My Problem is that i have an Impuls which is 100 uS long and i have to measure it with 2 ADCs. I know that...
Hi,
What will happen when we press the service discovery button in the master control panel? do we get any event like BLE_GAP_EVT_CONNECTED? I couldn't find any detail regarding...
I'm looking for information to start developing BLE slaves with nRF51822, but I can't find any datasheets/SDK. Do I need to buy the Development Kit in order to have that?...
I have an issue with my keyboard working with the windows suface (on windows 8.1). Occasionally, the last character sent is repeated several times instead of one. I do not...
On the nRF51822, I see that by programming the readback protect register, one can prevent reading code regions 0 and 1 from the SWD interface. However, if one had access to...
Hi,
I just watched a webinar from the bluetooth SIG on how to create source code from the nRFgo Studio for the nRF8001. Is the same possible for the nRF51822? To create...
Hi,
We modified the ble_app_hrs code to work with accelerometer peripheral, and we have created some custom characteristics with custom uuid's. Now we need to set the device...
Hello, Everyone:)
Nice to meet you !
Please could you commennt my first question on this community zone.
I've a question for the accuracy of synthesized clodk 32k on...
Hi
i am using NRf51822 custom board. In that i have NOR(spi0) and LED(i2c0).
But switching from spi0 to i2c0 is not possible so that i am not able to switch
off led...
