Hello,
I have not found any information about the VBUS current consumption. Is this information available? Do you know how much current flows through the VBUS pin?
Thank...
I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
nrf Connect Terminal overwrites LD_LIBRARY_PATH. I have added SEGGER JLink path to it so nrfjprog and JLink can dynamically link to the JLink dot so files. This works on Bash...
I am running nrf5340_audio_applications on the nRF5340 Audio DK. Follow the requirements, i add an external flash shield. I've only changed
the configuration of flash and...
Hello, I am trying to flash the nRF52840 SoC on the nRF52840 DK using an external J-Link debugger, without relying on the interface MCU or the onboard J-Link. My current switch...
Dear Nordic Engineers
I used NCS2.9.0 to develop a device based on nRF52840 and I would like to use UART to DFU the device based on SMP.
Now, I test SMP samples and use...
Hi,
After the latest update, the below setting allowing me to select nrfjprog as my device provider is now gone:
I am using the nRF Playground Docker container...
Hi,
I have been using NUS code to stream data between mobile and nrf5340 audio dk. is it possible to stream 256KB of data at a go? what is the maximum MTU size that i can...
I am using nrf connect sdk 2.7.0 with nrf52811.
My application is based on nrf5-sdk V 17.1.0 but now i want to port it to nrf-conneck sdk 2.7.0.
I want to know whether...
I have a problem with the package with nrf5 sdk, there for pca10100 examples are not there. i am trying to interface quadrature decoder with one encoder and it is not able...
Hello,I have a custom board using a Nordic nrf52823 microcontroller on it. I am using VSCode with the nrf connect SDK and the Zpehry RTOS- I want to make use Zephyr RTC to...
Is there any relevant assessment or introduction document of IC FMEA?
For example, the impact of abnormal short circuit and ordinary short circuit on chip 52832;
And...
1、I used the spi_bitbang routine to port it to the network core to run, and after the program was burned, I used an oscilloscope to measure the CLK pin waveform and there...
Hi,i I am testing the sample(ncs\v2.7.0\zephyr\samples\drivers\spi_bitbang) at a 52840DK board, with overlay setup like these:
spibb0: spibb0 {
compatible = "zephyr...
Hi nRF support team,
I am trying to add a new Custom Service and Characteristic an application on nRF82540 development kit using the nRF Connect SDK.
Can you please let...
Hello.
1. The nPM1300 PS v1.1 states in Section 6.1.1 the fllowing: "The default current limit is IBUS100MA (100 mA)". But the values after reset in registers VBUSINILIMSTARTUP...
