Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
how to resolve this linker error in keilv5 0

Hi Hakon.... when i compile my project i get some linker errors, ._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
1391 views

0 replies

Started over 10 years ago
by ali zaidi
Not Answered
iOS and pairing 0

I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
- pairing
- ios
5397 views

0 replies

Started over 10 years ago
by Nikita
Not Answered
Problems creating new MasterEmulator object v2.1.7 0

I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
- create
- constructor
- vs2010
- v2.1.7
598 views

0 replies

Started over 10 years ago
by Hugh
Not Answered
How to clear/reset of the GPIO configuration before System ON mode 0

Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset. How should I do...
802 views

0 replies

Started over 10 years ago
by yao
Not Answered
multiple link using iPhone 0

Hi, everyone~ My goal is to collect data from 4 sensors simultaneously using iPhone. Now, my testing code for sensor nodes is working fine. It was built based on the...
- s120
- iphone
- multiple link
- beacon kit
- ble
- evaluation kit
- 110
- nrf51822
989 views

0 replies

Started over 10 years ago
by shuoyu_ding

Recent in Nordic blog

Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018