Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SoftDevice BLE chained advertisement not reassembled by Bluez Stack 0

Hi, I am trying to configure an Xiao Seeed Studio nrf54l15 sense to transmit pre-processed sensor data via BLE extended advertisements. As the payload is more than 251 bytes...
11 views

0 replies

Started 2 hours ago
by rory0
Not Answered
nRF9151 Max Data Rate with v2.0.0 PHY firmware 0

In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
4 views

0 replies

Started 3 hours ago
by Zach Williams
Not Answered
nRF5340 (NCS v2.8.0) - External rail-to-rail LFXO source: boot hangs, external oscillator stops toggling 0

I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
21 views

0 replies

Started 9 hours ago
by Alvaro Arnaiz
Not Answered
Azure FOTA w/o Partition Manager (NCS v2.9.3) 0

Hi, I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ? Trying to build this gets...
38 views

0 replies

Started 10 hours ago
by Andrei H.
Not Answered
RF matching network when replacing DK antenna with SMA / external antenna 0

Hi Nordic team, I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571). For...
- development
- nRF54LM20A
- rf design
- hardware
- nRF7002
17 views

0 replies

Started 11 hours ago
by Samuel012

Recent in the DevZone Blog

Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015
How to use the latest Keil 5 for Keil 4 projects (.uvproj)

Stefan Birnir Sverrisson

As many have noticed, Keil 5 does not have native support for Keil 4 projects (project files ending with uvproj), it only has native support for Keil 5 projects (project files ending with uvprojx). However…
- 26 Mar 2015
The Google UriBeacon Project

Jason

Overview The UriBeacon design allows a Bluetooth Low Energy (BLE) device to periodically transmit an ADV packet that contains a URI. This technology enables any device, place or thing to become a beacon…
- 17 Mar 2015
Flashing SoftDevice directly from ARM Keil uVision and Makefile (nRF51 SDK 8.0.0)

Krzysztof Chruscinski

Since nRF51 SDK version 8.0.0 SoftDevices binary files have become a part of the release. In order to make it easier to flash proper type and version of SoftDevice a new feature was added: each project…
- 16 Mar 2015
6LoWPAN for Bluetooth low energy on OpenWRT

Glenn Ruben Bakke

OpenWRT is one of the most popular open source Linux-based router firmware alternatives for commodity routers. From kernel 3.17, Linux has supported 6LoWPAN for Bluetooth low energy (BLE) through the…
- 13 Mar 2015