Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Configure the nRF52840 as a radio co-processor for Thread. 0

Hello everyone, I’m trying to set up an nRF52840 dongle as a Thread radio co-processor to integrate with my Home Assistant setup. I followed the instructions in this Nordic...
72 views

0 replies

Started 4 hours ago
by Voslex
Not Answered
Current draw on nrf9160 0

Hi, I have a custom board running with the nrf9160. It also has the npm1300. I have it set up so that it is configuring the pmic and then turns off the cell and goes to sleep...
21 views

0 replies

Started 4 hours ago
by dave
Not Answered
i2s_read() Error -5 in Using SPH0465 with nRF52832 0

Hi there, I am trying to interface SPH0465 microphone with nRF Dev Kit 52832 with the following configurations of I2S: I have followed the code from echo example...
18 views

0 replies

Started 5 hours ago
by umerhuzaifa
Not Answered
Firmware for PPK2 - Custom PPK2 board 0

Hi, I am planning to get the PPK2 fabricated and assembled using the HW files available for PPK2. Just wanted to check will I have issues loading FW on it since I don...
- software
- Evaluation
- Other
- product
24 views

0 replies

Started 7 hours ago
by Shashanktss
Not Answered
Calling sd_ble_gap_connect() for an already connected device 0

I work nRF52840 + nRF5 SDK(S140 v7.2.0) If I call sd_ble_gap_connect() for a DeviceAddress of an already connected device, what will be the result? What will be the error...
23 views

0 replies

Started 8 hours ago
by loquat

Recent in Nordic blog

Running MicroPython on an nRF91 Series device to create an Asset Tracker

Mariano Goluboff

I was looking at a way to run MicroPython on an nRF91 Series development kit to do a quick prototype with some existing Python code. The MicroPython Zephyr port was already quite advanced, so I added the…
- 22 Feb 2024
Control your smart home with the Wireless Wizard Wand

Tord Natlandsmyr

Bring magic to your home with the Nordic Semiconductor Wireless Wizard Wand. The wand utilizes the powerful nRF52840 chip with Edge Impulse ML motion recognition to communicate with all your smart home appliances…
- 12 Feb 2024
Automated emergency light testing through Bluetooth Mesh

DagE

During a summer internship at Nordic, I took on a project that focused on applying Bluetooth® Mesh technology in a practical setting. The project concentrated on making emergency lighting testing in commercial…
- 5 Feb 2024

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020