Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Deleted 0

Deleted

365 views

0 replies

Started over 3 years ago
by liammcnair
Not Answered
nRF9160 LTE and GPS matching network 0

Hi , I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
635 views

0 replies

Started over 3 years ago
by Netanel
Not Answered
When porting Arduino i2c sensor driver to nrf52... 0

I am a student interested in Nordic. My coding skills are very poor. So I want to get help. I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
746 views

0 replies

Started over 3 years ago
by eggmoneyna
Not Answered
low level interrupt not firing after porting from SDK 15.3 to SDK 17.0.2 0

I have a working project where pin 16 is configured as a low-level interrupt source. it is working well with SDK 15.3 after porting to SDK 17.0.2, it is not triggering...
374 views

0 replies

Started over 3 years ago
by kobyfr
Not Answered
Thank you 0

Hello Nordic Support Engineers and fellow developers ... Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
508 views

0 replies

Started over 3 years ago
by Tim

Recent in Nordic blog

Nordic nRF51822 ARM Cortex-M0 Development using emIDE

Hugh

Nordic nRF51822 ARM Cortex-M0 Development using emIDE To avoid the hefty charges with commercial compilers I tried emIDE with some success; here are the settings I used for the EV Kit Official emIDE…
- 22 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014

Latest guides

Getting Started : Getting started with Bluetooth Electronic Shelf Labels (ESL) and Periodic Advertising with Responses (PAwR)

Lorenzo Amicucci

The new Bluetooth 5.4 features Periodic Advertising with Responses (PAwR) and Encrypted Advertising Data (EAD) can be used for one-to-many applications. One of these is the Electronic Shelf Labels (ESL…
- 7 Aug 2024
nRF5x: General PCB design guidelines for nRF52 series

Kaja

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 6 Nov 2023
Software: Periodic Advertising with Responses (PAwR): A practical guide

Hung Bui

Periodic Advertising with Responses (PAWR) is a new feature in Bluetooth 5.4. It extends the periodic advertising protocol from Bluetooth 5.0. Periodic advertising, where a device sends broadcast data with…
- 13 Sep 2023
nRF5x: General PCB design guidelines for nRF53 series

Kaja

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 6 Jul 2023
Software and Protocols: nRF Cloud Access Provisioning

Charlie

Please note that some information on this page may be outdated due to ongoing improvements in nRF Cloud. For the most current details on provisioning services, refer to the nRF Cloud Security Services…
- 1 Dec 2022
Software and Protocols: Field verification of GNSS on the nRF91 Series

JaniM

Introduction The intention of this guide is to clarify and describe the main aspects relevant to the GNSS receiver functionality on the nRF9160 as well as build configurations, tool recommendations and…
- 10 Jun 2022