Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
NRF52805 DTM setup reset command failed 0

I using nrf52805 for DTM, in sdk17.1, pca10040e. I only changed RXTX pin number, but did not modify the rest. Then use Nordic Connect for DTM testing, and the following prompt...
10 views

0 replies

Started 34 minutes ago
by zhangchenfang
Not Answered
DYNAMIC_INTERRUPTS Fail in "esb_ptx" Sample 0

HI, I am building "esb_ptx" sample in NRF54L15-PDK, by using CONFIG_DYNAMIC_INTERRUPTS, but it;s always reset like below;How to config the prj.conf to enable CONFIG_DYNAMIC_INTERRUPTS...
10 views

0 replies

Started 37 minutes ago
by gandyhuang
Not Answered
Output pins configured in the Overlay, not showing in Devicetree view 0

I have the following setup in my overlay file: relay { compatible = "gpio-relay"; relay1: relay_1 { gpios = <&gpio0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; label = "DC Mtr...
16 views

0 replies

Started 1 hour ago
by MontanaEE
Not Answered
Move console, bt-mon, etc to RTT 0

I need to move everything off of UART0 so I can use it for my touchscreen On a previous post I was told I could move everything to RTT in the overlay, but when I try to...
16 views

0 replies

Started 1 hour ago
by MontanaEE
Not Answered
The relation for PIN reset and other reset 0

Sorry for long sentence. The nRF5340 document describes about the Reset. This chip set have the POR. so, if POR function work, I don't need to use the PIN reset. because POR...
15 views

0 replies

Started 1 hour ago
by FACE@shibuya

Recent in Nordic blog

Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018

Latest guides

Bluetooth low energy: Wireless timer synchronization among nRF5 devices

Audun

Introduction In a variety of use cases there is a need to share a common clock among multiple devices. Such a common clock can be used for many purposes, for example by having each node in a network perform…
- 12 Jul 2016
nRF5x: General PCB design guidelines for nRF52 series

FormerMember

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 11 Jul 2016
Software Development Kit: Migrating to Peer Manager

Øyvind Rønningstad

The tutorial has been updated for SDK v11, which contains the production-ready release of Peer Manager. The original tutorial can be found on this page, below the updated tutorial. #Migrating to Peer…
- 8 Apr 2016
Bluetooth low energy: Bluetooth low energy Characteristics, a beginner's tutorial

MartinBL

Before we begin Table of content Topics that will be covered include: Before we begin Basic theory Attribute tables in nRFConnect Bluetooth Low Energy application Description of the example Adding a…
- 18 Mar 2016
Bluetooth low energy: Bluetooth Smart and the Nordic's Softdevices - Part 2 Connection

Hung Bui

This blog series was created as an attempt to fill in the gap between how Bluetooth Smart is described in the spec and how you can use our APIs and event from our softdevice to do what defined in the spec…
- 1 Feb 2016
Design Examples: Capacitive Touch on the nRF52 series

Einar Thorsrud

Important updates: Due to erratum 84 (COMP: ISOURCE not functional), capacitive sensing using the relaxation oscillator method is not usable in a real product with the nRF52832, as it will only work reliably…
- 31 Jan 2016