Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Which timer is being used as RTOS tick in nrf connect sdk for nrf52811 0

I am using nrf connect sdk 2.7.0 with nrf52811. My application is based on nrf5-sdk V 17.1.0 but now i want to port it to nrf-conneck sdk 2.7.0. I want to know whether...
8 views

0 replies

Started 55 minutes ago
by sumit-adep
Not Answered
Can't use CONFIG_FPROTECT=y in MCUBOOT+APP (with TFM), compilation results in "No fprotect backend selected." CMake error 0

Hi all, I wanted to enable read/write protection for MCUBOOT partition in my firmware from the application and encountered a strange problem. The build (build system - default...
- development
- software
- nRF9160
- flash
13 views

0 replies

Started 4 hours ago
by valerii7
Not Answered
pin 9 configuration. 0

I have an application that tries to configure pin 9 of port 0 on the nrf52840. this pin is reserved for NFC use. in one application it was enough to add: & uicr { nfct...
21 views

0 replies

Started 7 hours ago
by shlomots
Not Answered
Questions about NFC in nRF54L15 0

Hi ! May I ask if the NFC function of the nRF54L15 needs to be powered when it is used as an NFC tag? Because ordinary NFC cards have no power supply and their operation...
- development
- software
- nRF54L15
- nfc
21 views

0 replies

Started 8 hours ago
by listenYes
Not Answered
Welcome page and Application page not found for some project 0

Hi DevZone, As mentioned in the title, the Welcome page and Application page won't show any selection for my project as following image shown. My project is based on...
23 views

0 replies

Started 12 hours ago
by Benneb

Recent in Nordic blog

Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019