Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Seeking Recommendations for LTE Network Timeout Configuration 0

Background Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
- nRF9160
- lte-m
- nb-iot
- configuration
- production
10 views

0 replies

Started 20 minutes ago
by tareq_itx
Not Answered
nRF9151 DK External Power Supply Issue 0

Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
9 views

0 replies

Started 1 hour ago
by Yun531
Not Answered
nRF9160 SLM MQTT Connection 0

Hi all, I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
23 views

0 replies

Started 3 hours ago
by KR0731
Not Answered
Zephyr sample application Mesh and nRF Mesh applicatio 0

Hello, We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application. After going through the documentation and few other Q&A on the portal, I was...
- software
- Evaluation
- mesh
- zephyr
- nrf52840
17 views

0 replies

Started 5 hours ago
by gsMCHP
Not Answered
custom board 0

Hlo I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
20 views

0 replies

Started 6 hours ago
by sunaina

Recent in Nordic blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015