Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Is it possible to disable CLI commands from the NCS CLI sample? 0

Hi, I am using the NCS Thread CLI sample as the base of my project and I was wondering if it's possible to disable the cli command functionalities of this project to save...
0 views

0 replies

Started 3 hours ago
by Glenyz
Not Answered
Change west Toolchain 0

I have been using the nRF Connect VS Code extension. Some of my projects come from external sources, so I build them using the nRF Connect terminal and west commands. I...
0 views

0 replies

Started 3 hours ago
by Manieldyers
Not Answered
nrf5340 reflow profile 0

I need a reflow profile for the nRF5340. Is there anywhere I can find this specific to this part?
0 views

0 replies

Started 3 hours ago
by cdeckerSMC
Not Answered
HTTPS Connection using Serial LTE Modem application 0

Hello, I apologize if this is a simple question. I am working with the nRF9161-DK and am using the Serial LTE Modem application. The ultimate goal is to send data via...
0 views

0 replies

Started 6 hours ago
by iiwiiDev
Not Answered
NRF52811-CAAA ADC Input pins 0

Hi, In nRF52811-CAA chip, which pins are allocated to ADC inputs. In Table 122 of datasheet which shows pinout for WLCSP package, it just mentions AIN1, AIN2, and AIN3....
0 views

0 replies

Started 7 hours ago
by Kaveh.M

Recent in Nordic blog

Programming nRF52832 boards in Python with Zerynth

lfcerf

Released in December 2016, the new Bluetooth 5 offers truly exciting possibilities for home, industry, and commerce as well as the more traditional areas of wearables and personal devices historically…
- 7 Jun 2017
Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019