Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
FPROTECT for NRF54L10 0

I'm working with NRF54L10 module. I needed more mcuboot space so in pm_static.yml I allocated it 80kb. Before this FPROTECT was working but after I allocated 80kb, now FPROTECT...
3 views

0 replies

Started 12 minutes ago
by Amaan Singh
Not Answered
how to connect nrf52840 into mesh of 50 device 0

how to create the nrf52840 mesh of more than 50 devices ? I am using the chat sample for this mesh network but i am tested with the 12 boards but i am getting reply from...
9 views

0 replies

Started 4 hours ago
by sibi
Not Answered
zephyr/samples/net/cloud/aws_iot_mqtt fails to connect to aws 0

I have nordic board nrf5340-dk + nrf7002-ek I want to run on it the application zephyr/samples/net/cloud/aws_iot_mqtt I built the project and I flashed on my device I can...
- software
- Evaluation
- Wi-Fi
- zephyr
- nRF5340
15 views

0 replies

Started 4 hours ago
by MOHAMED Kallel
Not Answered
nRF5340 PDM CLK waveform 0

Hi We use nRF5340, set GPIOs as PDM for DMIC device, and measure waveform as below The PDM DATA high level will decrease periodically Is this waveform normal? If yes...
11 views

0 replies

Started 7 hours ago
by Poki Huang
Not Answered
BLE Mesh replay protection triggered during burst vendor message transmission via GATT Proxy 0

Hello, I am developing a Bluetooth Mesh application using Nordic hardware and am running into reliability issues when transmitting bursts of vendor messages. System overview...
- development
- java
- software
- beginner
- Failure Analysis
- debugging
- android
- mesh
- configuration
- C
- nrf52840
26 views

0 replies

Started 16 hours ago
by mromano

Recent in the DevZone Blog

Programming the nRF51822 Beacon Kit with the nRF51DK

Stefan Birnir Sverrisson

One way to program the nRF51822 Bluetooth Smart Beacon Kit is to use the nRF51 DK. This gives you a full scale development platform (the nRF51 DK). This blog will go thru the steps needed to program…
- 7 May 2015
Bluz, a cloud connected Bluetooth LE development kit based on the nRF51822, is live on Kickstarter

eric ely

Bluz is a brand new development kit that brings Bluetooth LE to the internet. We have paired up with Spark and ported their FW to the nrf51822, allowing Bluz to be controlled and programmed over the…
- 15 Apr 2015
nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015
Building kernel for RPi2 with bluetooth_6lowpan for Raspbian

Håkon Alseth

Building kernel for RPi2 with bluetooth_6lowpan In this guide, you will have two choices: Cross-compilation build Native build Choose the one that fits your needs. Cross-compilation is…
- 9 Apr 2015
Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015