Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF52805 BLE throughput sample 0

Hi Nordic Semiconductor Expert, I would like to measure the BLE throughput over nRF52805. Seeing BLE Throughput sample in nRF Connect SDK below, this SoC platform is...
- development
- nRF52805
- software
- nRF Connect SDK
- flash
- bluetooth le
- ram
24 views

0 replies

Started 49 minutes ago
by Felipe1
Not Answered
Number of UARTs available for 2AB (nRF53840) 0

Hi, I would like to know Number of UARTs available for Murata 2AB. According to the 2AB datasheet, there is one UART, but the nRF52340 datasheet shows two UARTs. Can 2AB...
22 views

0 replies

Started 4 hours ago
by Tsutsumi
Not Answered
[nRF7002DK] HTTPS request Failed with errno: 22 0

Hi! Im using nRF7002DK for start HTTPS connection. I started with the example from Lession 5 exercise 2 in the nRF dev academy. lession5 exercise 2 I changed the...
16 views

0 replies

Started 4 hours ago
by DDYD1
Not Answered
nrf5340 occasionally stuck on BT_CONN_STATE_DISCONNECTING 0

Hello, We have an nrf5340 custom board and during frequent BLE connections/disconnections sometimes it seems the netcore gets stuck. We are connecting to an iOS app and...
26 views

0 replies

Started 7 hours ago
by tonyh
Not Answered
Device firmware update (DFU) over NFC 0

Hi for DFU is bluetooth used by default. Your DFU app suports only using bluetooth to do a DFU. Do you have any tools to do a DFU over NFC? Or do I have to write a tool...
25 views

0 replies

Started 7 hours ago
by Marelcom

Recent in Nordic blog

Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019