Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Failed to set MCUboot secondary to external flash. E: Failed to open flash area ID 2 (image 0 slot 1): -2, cannot continue 0

I have problem placing MCUboot secondary to external flash. I have been testing using nRF9160DK. Project compiles fine but device doesn't boot after flashing the firmware...
0 views

0 replies

Started a few seconds ago
by mmade
Not Answered
nRF52833 SAADC issue 0

I have a photodiode, and under indoor lighting conditions, the reading on the oscilloscope is about 150mV. When I connect it to an Arduino Uno or Adafruit nRF52840 Sense,...
- development
- adc
- nRF52833
- hardware
3 views

0 replies

Started 11 minutes ago
by Ziyao Zhou
Not Answered
How to delete the default child_image or configure it to my own cpunet project 0

mcu: nrf5340 board: nrf5340dk_nrf5340_cpuapp sdk: v2.6.1 When I configure CONFIG_BOARD_ENABLE_CPUNET to enable cpunet, there isn't an issue. However, when I configure...
14 views

0 replies

Started 1 hour ago
by kpi_xie
Not Answered
NRF Cloud coap payload size limitation too small 0

Hi, I am using NRF Cloud + coap comms to send data. However I have encountered payload size limitations that are not configurable via KConfig: sdk-nrf/subsys/net/lib/nrf_cloud...
12 views

0 replies

Started 1 hour ago
by AdrianT
Not Answered
nRF52805 BLE throughput sample 0

Hi Nordic Semiconductor Expert, I would like to measure the BLE throughput over nRF52805. Seeing BLE Throughput sample in nRF Connect SDK below, this SoC platform is...
- development
- nRF52805
- software
- nRF Connect SDK
- flash
- bluetooth le
- ram
33 views

0 replies

Started 2 hours ago
by Felipe1

Recent in Nordic blog

BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019