Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
GPIOTE PORT event wake from WFE (System ON, SEVONPEND + Errata 220 workaround) takes ~14-15 µs to actually resume CPU execution — expected, or a known behavior? 0

Hi, I am using nrf52832 with softdevice s112 and SDK 17.1.0 Is a ~14-15 µs latency between a GPIOTE PORT event becoming pending (via DETECT / LATCH , SENSE + LDETECT on...
- development
- software
- s112
- nrf52832
23 views

0 replies

Started 4 hours ago
by Justin
Not Answered
nRF Boards debug out Cable and its adapter 0

I currently have nRF52/53/54 Development Kits and would like to utilize their onboard J-Link debugger by connecting through the Debug-Out Port (P19). However, I have observed...
29 views

0 replies

Started 10 hours ago
by RaviDebugs
Not Answered
Allow nRF Cloud A-GNSS with caller-supplied network info without using MODEM_INFO 0

Using nRF Connect SDK v3.4.1 with an nRF9151. CONFIG_NRF_CLOUD_AGNSS currently has unconditional dependencies on: depends on MODEM_INFO depends on MODEM_INFO_ADD_NETWORK...
43 views

0 replies

Started 1 day ago
by Regan0
Not Answered
Typo in nRF Connect SDK Intermediate Lesson 9 Exercise 2 DFU with custom keys 0

In step 2.3, when targeting nRF54L Series DK, SB_CONFIG_MCUBOOT_GENERATE_DEFAULT_KEY_FILE is misspelled.
60 views

0 replies

Started 2 days ago
by David Shimizu
Not Answered
nRF Cloud returns rate-limited 0

Hi I am working with nRF Cloud - using a developer account (limited to 10 devices). After connecting a few times with a device (using a different serial each time),...
55 views

0 replies

Started 2 days ago
by garrettb

Recent in the DevZone Blog

nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015